(2)
Install the new retainers (6) and the new packing (7).
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 32-11-13Page 458 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(3)
Install the new wiper ring (13). Make sure that the wiper ring (13) is correctly installed. The open U section points out.
(4)
Install the new seals (1) and (2).
(5)
Use the KEEP RING (460003180-74) to make the seal (2) go back to its initial condition.
(6)
Use a smooth edged tool to carefully install each part of the seal
(2) in the correct position.
(7)
Use the ASSEMBLY SLEEVE (460006405) to carefully install the lower bearing (4) on the sliding tube (5).
(8)
Put the bearing (15) on the upper bearing housing (18). Do not cover the holes for the pins (14) and (17).
(9)
Install the upper bearing housing (18) on the sliding tube (5). Make sure that the holes in the upper bearing housing (18) align with the holes in the sliding tube (5).
(10)
Install the diaphragm tube assembly (3) into the sliding tube (5).
(11)
Install both parts of the retaining collar (16) in the sliding tube
(5) with the larger diameter at the top. Make sure that the holes align with the holes in the upper bearing housing (18).
(12)
Use the ASSEMBLY AND EXTRACTION TOOL to install the pin (14) in the larger diameter hole. Install the pins (17) in the other holes.
(13)
Install the bearing (15) in its groove to cover the pins (14) and (17).
**ON A/C 051-052,
Subtask 32-11-13-420-052
A. Preparation for Installation
(1)
Use a clean MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean the seal grooves.
(2)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(3)
Do an inspection of the component interface and/or the adjacent area.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-11-13Page 459 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
R (4) Use a clean lint-free cloth to dry the seal grooves.
R (5) Lubricate the new items that follow with HYDRAULIC FLUIDS (Material
R No. 02-001) or HYDRAULIC FLUIDS (Material No. 02-004):
R - seal (1)
R - seal (2)
R - retainers (6)
R - packings (7)
R - seal (8)
R - seal (9)
R - sealing ring (10)
R - joint seal (11)
R - wiper ring (12).
R NOTE : In the step that follows, make sure that the Materials No.____
R 04-004 and No. 04-022 are not mixed together. Do not use them
R at the same time (Ref. SIL 12008).
R (6) Apply a thin layer of COMMON GREASE (Material No. 04-004) or COMMON
R GREASE (Material No. 04-022) on the internal surface of the lower
R bearing housing (4).
R Subtask 32-11-13-420-051
R B. Installation of the MLG Shock-Absorber Gland-Seals
R (1) Install the new sealing ring (10), the new joint seal (11) and the
R new seals (8) and (9).
R NOTE : There are two types of seal (8) available, a standard seal and____
R a wedgepak seal. The seal types are fully interchangeable but
R it is recommended that a wedgepak seal is installed. The
R wedgepak seal must not be installed in the bottom (primary)
R position of the lower bearing housing (4). Refer to VSB
R 200-32-240 for data.
R (2) Install the new retainers (6) and the new packings (7).
R (3) Install the new wiper ring (12). Make sure that the wiper ring (12)
R is correctly installed. The open U section points out.
R (4) Install the new seals (1) and (2).
R (5) Use the KEEP RING (460003180-74) to make the seal (2) go back to its
R initial condition.
R 1EFF : 051-052, 1 32-11-13Page 460 1 1 May 01/05 1 1 1CES 1
R R (6) Use a smooth edged tool to carefully install each part of the seal (2) in the correct position.
R R (7) Use the ASSEMBLY SLEEVE (460006405) to carefully install the lower bearing (4) on the sliding tube (5).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(31)
