(6)
Apply a thin layer of COMMON GREASE (Material No. 04-004) or COMMON GREASE (Material No. 04-022) on the internal surface of the lower bearing housing (4).
(7)
Use a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean the AREA A on the tube assembly (19), and the interface of the sliding tube sub-assembly (24).
(8)
Apply a thin layer of SPECIAL MATERIALS (Material No. 05-002) to the AREA A on the tube assembly (19), and the interface of the sliding tube sub-assembly (24).
R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 401-499,
Subtask 32-11-13-420-055-B
A. Preparation for Installation
(1)
Use a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean the seal grooves and the interfaces of the jacking dome (22).
(2)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(3)
Do an inspection of the component interface and/or the adjacent area.
(4)
Use a clean lint-free cloth to dry the seal grooves.
(5)
Lubricate the new items that follow with HYDRAULIC FLUIDS (Material No. 02-001) or HYDRAULIC FLUIDS (Material No. 02-004):
-
seal (1)
-
seal (2)
-retainers (6)
-packings (7)
-
seal (8)
-
seal (9)
-sealing ring (10)
-joint seal (11)
-wiper ring (13)
-O-ring (20)
-backing ring (21).
NOTE : In the step that follows, make sure that the Materials No.
____ 04-004 and No. 04-022 are not mixed together. Do not use them at the same time (Ref. SIL 12-008).
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 32-11-13Page 485 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(6)
Apply a thin layer of COMMON GREASE (Material No. 04-004) or COMMON GREASE (Material No. 04-022) on the internal surface of the lower bearing housing (4).
(7)
Use a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean the AREA A on the tube assembly (19), and the interface of the sliding tube sub-assembly (24).
(8)
Apply a thin layer of SPECIAL MATERIALS (Material No. 05-002) to the AREA A on the tube assembly (19), and the interface of the sliding tube sub-assembly (24).
**ON A/C 051-052,
Subtask 32-11-13-420-055
A. Preparation for Installation
(1)
Use a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean the seal grooves and the interfaces of the jacking dome (21).
(2)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(3)
Do an inspection of the component interface and/or the adjacent area.
(4)
Use a clean lint-free cloth to dry the seal grooves.
(5)
Lubricate the new items that follow with HYDRAULIC FLUIDS (Material No. 02-001) or HYDRAULIC FLUIDS (Material No. 02-004):
-
seal (1)
-
seal (2)
-retainers (6)
-packings (7)
-
seal (8)
-
seal (9)
-sealing ring (10)
-joint seal (11)
-wiper ring (12)
-O-ring (19)
-backing ring (20).
NOTE : In the step that follows, make sure that the Materials No.
____ 04-004 and No. 04-022 are not mixed together. Do not use them at the same time (Ref. SIL 12-008).
R 1EFF : 004-049, 051-099, 101-149, 151-199, 1 32-11-13Page 486 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 1EFF : 051-052, 301-399, 1 32-11-13Page 487 1 1 May 01/05 1 1 1CES 1
R R R (6) Apply a thin layer of COMMON GREASE (Material No. 04-004) or COMMON GREASE (Material No. 04-022) on the internal surface of the lower bearing housing (4).
R R R (7) Use a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean the AREA A on the tube assembly (18), and the interface of the sliding tube sub-assembly (23).
R R R (8) Apply a thin layer of SPECIAL MATERIALS (Material No. 05-002) to the AREA A on the tube assembly (18), and the interface of the sliding tube sub-assembly (23).
**ON A/C 301-399,
Subtask 32-11-13-420-055-C
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(38)
