(c) Disconnect the axle harness electrical connector 4052VC (4053VC)
 (7) from the connector (8) installed on the bracket (9).
 (3)
 Carefully remove the six cableforms of the 1M and 2M harnesses from the axle through the cable access holes. Do not make kinks in the harnesses.

 (4)
 Put blanking caps on the disconnected electrical connectors.

R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-43Page 454 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1

 **ON A/C ALL

 TASK 32-11-43-400-003
 Installation of the 1M and 2M Harnesses on the MLG Axle
 WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______ NOTICES ARE IN POSITION.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific draw strings No specific safety barriers No specific warning notice No specific access platform 2.0 m (6 ft. 7 in.)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 08-048  D DA-2-657-4 ADHESIVE (Ref. 20-31-00)
 Material No. 09-016  USA MIL-PRF-81733D TYPE II CLASS B CORROSION INHIBITING FILLET CONSISTENCY (Ref. 20-31-00)
 Material No. 11-026 GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 16-016 C Z-12.383 EXTERNAL DECORATION PAINT (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 1EFF : ALL 1 32-11-43Page 455 1 1 May 01/05R 1 1 1CES 1

 -------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 19-010  USA AMS 5687
 LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA
 (Ref. 20-31-00)

 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power 32-00-00-481-001 Installation of the Safety Devices on the Landing
 Gears
 32-12-00-010-001 Open the Main Gear Doors for Access
 32-12-00-410-001 Close the Main Gear Doors after Access
 32-41-11-000-006 Removal of the MLG Wheel

 (2649GM,2650GM,2651GM,2652GM)
 32-41-11-400-006 Installation of the MLG Wheel

 (2649GM,2650GM,2651GM,2652GM) 32-42-27-000-001 Removal of the Brake (2641GM,2642GM,2643GM,2644GM) 32-42-57-000-001 Removal of the Tachometer 32-42-57-400-001 Installation of the Tachometer 32-48-51-000-005 Removal of the Fan Assy (7GS,8GS,9GS,10GS) 32-48-51-400-005 Installation of the Fan Assy (7GS,8GS,9GS,10GS) 32-49-18-000-001 Removal of the Rotating Mechanism 32-49-18-400-001 Installation of the Rotating Mechanism 32-69-00-740-001 BITE Check Landing Gear Control Interface Unit
 (LGCIU) using MCDU to Ensure that Continuous BITE is Operative
 **ON A/C 001-003, 051-052,
 32-11-43-991-028  Fig. 408
R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 32-11-43-991-028-A  Fig. 408A
 1EFF : ALL 1 32-11-43Page 456 1 1 Aug 01/05 1 1 1CES 1 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

**ON A/C ALL
 32-11-43-991-029 Fig. 409
 3. Job Set-up
__________
 Subtask 32-11-43-941-056
 A. Safety Precautions
 (1)
 Make sure that the safety barriers are in position.

 (2)
 Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).

 (3)
 On the panel 400VU:

 -
make sure that the landing-gear control-lever 6GA is in the DOWN position

 -
make sure that the warning notice is in position to tell persons not to operate the landing gear.

 Subtask 32-11-43-869-060
 B. Flight Configuration Precautions
 (1) If you did not open the LGCIU circuit breakers, make sure that the electrical circuits are de-energized (Ref. TASK 24-41-00-862-002).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(122)