R NOTE : In the step that follows, make sure that the Materials No.____
R 04-004 and No. 04-022 are not mixed together. Do not use them
R at the same time (Ref. SIL 12-008).
R (7) Lubricate these parts with COMMON GREASE (Material No. 04-004) or
R COMMON GREASE (Material No. 04-022):
R - the pins (20) and (21)
R - the bushes in the side-stay bracket
R - the seal (32)
R - the bores of the MLG attachment lugs.
R Subtask 32-11-18-420-050-A
R B. Installation of the MLG Side-Stay
R WARNING : BE CAREFUL WHEN YOU REMOVE OR INSTALL THE MLG SIDE-STAY. IT_______
R WEIGHS 62.5kg (137.5lb).
R (1) Install the new seal (32) in the bush (33).
R (2) Lift the side-stay (6) into position with the hoist and install the
R cardan joint (5) in the side-stay bracket.
R (3) Use a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING
R AGENTS (Material No. 11-026) to clean the thread of the cardan joint
R (5).
R (4) Apply SPECIAL MATERIALS (Material No. 05-047) to the thread of the
R cardan joint (5).
R (5) Install the washer (1) and the nut (2) and tighten the nut (2) by
R hand.
R (6) Loosen the strap (but not fully) on the HOIST (98D32104013004).
R (7) Move the side-stay (6) about the the side-stay center joint and
R install the cardan joint (7) in the MLG attachment lug.
R (8) Use a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING
R AGENTS (Material No. 11-026) to clean the thread of the cardan joint
R (7).
R (9) Apply SPECIAL MATERIALS (Material No. 05-047) to the thread of the
R cardan joint (7).
R (10) Install the nut (8) and tighten by hand.
R (11) Disconnect the cables from the hook.
R (12) Disconnect the strap and remove the HOIST.
R (13) To tighten the nut (2):
R (a) Push the MLG as far as possible to the closed position. This will
R make sure that the cardan joint (5) is installed fully in the
R side-stay bracket.
R (b) Use the TORQUE ADAPTOR (460005812) to TORQUE the nut (2) to 25.0
R m.daN (184.36 lbf.ft).
R (c) Loosen the nut (2).
R (d) Do the steps (a), (b) and (c) two more times.
R (e) Use the TORQUE ADAPTOR to TORQUE the nut (2) to 18.0 m.daN
R (132.74 lbf.ft).
R (14) To tighten the nut (8):
R (a) Push the MLG as far as possible to the closed position. This will
R make sure that the cardan joint (7) is installed fully in the MLG
R leg assembly.
R (b) Use the TUBE SPANNER (460007272) to TORQUE the nut (8) to 40
R m.daN (294.98 lbf.ft).
R (c) Loosen the nut (8).
R (d) Do the steps (a), (b) and (c) two more times.
R (e) Use the TUBE SPANNER to TORQUE the nut (8) to 16.2 m.daN (119.46
R lbf.ft).
R (15) Use a feeler gage to measure the dimensions W and X as follows:
R (a) For in-service components:
R - the total clearance must be between 0.05 mm (0.0019 in.) and
R 0.5 mm (0.0196 in.).
R (b) For repaired or overhauled components:
R - the total clearance must be between 0.05 mm (0.0019 in.) and
R 0.2 mm (0.0078 in.).
R (16) Use a feeler gage to measure the dimensions Y and Z as follows:
R NOTE : The clearance can change around the pin and the bush____
R circumference. This is permitted if the maximum clearance is
R the dimension used in all the calculations.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(72)
