C. Get Access
(1)
Remove the applicable MLG brakes (Ref. TASK 32-42-27-000-001) and the wheels (Ref. TASK 32-41-11-000-006).
(2)
Release the electrical harnesses from the clamps attached to the upper and lower torque links (Ref. TASK 32-11-43-000-001).
(3)
Release the hydraulic dressings from the clamps attached to the upper and lower torque links (Ref. TASK 32-11-12-000-001).
4. Procedure
_________
**ON A/C 001-003, 051-052,
(Ref. Fig. 401/TASK 32-11-27-991-001) R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 32-11-27-991-001-A)
**ON A/C 001-003, 051-052,
Subtask 32-11-27-020-053
A. Removal of the MLG Torque Links
(1)
Remove the torque link damper (Ref. TASK 32-11-29-000-001).
(2)
Disconnect the bracket assembly (23) as follows:
(a)
Remove and discard the cotter pin (26).
(b)
Remove the nut (25) and the washer (24).
(c)
Support and prevent damage to the rod (27) and remove the bolt (22).
1EFF : ALL 1 32-11-27Page 403 1 1 Aug 01/05 1 1 1CES 1
MLG Torque Link Assembly
Figure 401/TASK 32-11-27-991-001
R 1EFF : 001-003, 051-052, 1 32-11-27Page 404 1 1 May 01/05 1 1 1CES 1
MLG Torque Link Assembly
Figure 401A/TASK 32-11-27-991-001-A
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-27Page 405 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(3)
Remove the top torque link (9) as follows:
(a)
Remove and discard the cotter pin (5).
(b)
Remove the nut (4), the washer(s) (3) and the bolt (1).
(c)
Hold the top torque link (9), remove the pin assembly (29), the spacers (2) and then the top torque link (9).
(4)
If you are to replace the torque link (9), remove the nuts (6), the washers (7) and the bolts (28). Remove the bracket (23) and the plate (8).
(5)
Remove the bottom torque link (20) as follows:
(a)
Release the tab-washers (11) and remove the bolts (10). Remove and discard the tab-washers (11).
(b)
Remove the wedge (12).
(c)
Remove and discard the cotter pin (16).
(d)
Remove the nut (17) and the washer(s) (18).
(e)
Remove the bolt (15) and release the bonding strap assembly (13).
(f)
Hold and prevent damage to the fitting (14) and the electrical harness that is attached to its lower surface.
(g)
Hold the bottom torque link (20) and remove the pin assembly (21), the spacers (19) and then the bottom torque link (20).
R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 32-11-27-020-053-A
A. Removal of the MLG Torque Links
(1)
Remove the torque link damper (Ref. TASK 32-11-29-000-001).
(2)
Remove the top torque link (20) as follows:
(a)
Release the tab-washers (4), remove the bolts (3) and remove and discard the tab-washers (4).
(b)
Remove the wedge (5).
1EFF : ALL 1 32-11-27Page 406 1 1 Aug 01/05 1 1 1CES 1
(c)
Remove and discard the cotter pin (7).
(d)
Remove the nut (8), the washer(s) (6) and the bolt (2).
(e)
Hold the top torque link (20). Remove the pin assembly (21), the spacers (22) and then the top torque link (20) and the bracket (1).
(3) Remove the bottom torque link (18) as follows:
(a)
Release the tab-washers (10), remove the bolts (9) and remove and discard the tab-washers (10).
(b)
Remove the wedge (11).
(c)
Remove and discard the cotter pin (14).
(d)
Remove the nut (15), the washer(s) (16) and the bolt (12).
(e)
Hold and prevent damage to the fitting (13) and the electrical harness that is attached to its lower surface.
(f)
Hold the bottom torque link (18) and remove the pin assembly (19), the spacers (17) and then the bottom torque link (18).
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-27Page 407 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C ALL
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(95)
