_______
DO:
-FLUSH IT AWAY WITH CLEAN WATER
-GET MEDICAL AID. CAUTION : MAKE SURE THAT THE FLUID DOES NOT STAY ON THE AIRCRAFT
_______ STRUCTURE. IF THE FLUID GETS ON THE AIRCRAFT STRUCTURE, WASH IT OFF IMMEDIATELY WITH SOAP AND WATER.
(a) Put the container below the hose unions (32) and (43) and the hoses (37) and (38).
WARNING : CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE
_______ TASK. LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-11-16Page 421 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(b)
Remove and discard the lockwire and disconnect the hose unions
(32) and (43) from the hoses (37) and (38).
(c)
Remove and discard the lockwire from the nuts (39), (42), (36) and (33).
(d)
Loosen the nuts (39), (42), (36) and (33).
(e)
Remove the nuts (33) and (42) and the washers (34) and (41), and remove the hoses (37) and (38) from the bracket assembly.
(f)
Remove the washers (35) and (40) and the nuts (36) and (39) from the hoses (37) and (38).
(g)
Put blanking caps on the disconnected hose unions (32) and (43) and the hoses (37) and (38).
(6)
Disconnect the locksprings at their top attachment (Ref. TASK 32-11-19-000-003).
(7)
Install the SPLINT ASSEMBLY - SIDE STAY (98D32104013001) on the
side-stay assembly (6) with:
-
the cables to the wing surface
-
the strap to the wing surface
-
the center joint of the side-stay located in the center hole of the side-stay splint assembly.
(8)
Tighten the strap and connect the cables to the hook.
(9)
Remove the cotter pin (31), the nut (30) and the washer (29). Discard the cotter pin (31).
(10)
Hold the lockstay (28) (which weighs 3.4 kg (7.4957 lb)), and remove the pin (26) and the washer (27).
(11)
Carefully disengage the lockstay (28) from the cardan joint and collect the spacers (25).
(12)
Compress the lockstay actuator to fold the lockstay and safety the lockstay in this position.
(13)
Remove the circlip (4) as follows: (Ref. Fig. 404/TASK 32-11-16-991-007)
NOTE : Make sure that all the related parts are clean before you
____
remove the circlip (4).
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-16Page 422 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(a)
Use an applicable tool to release the tail of the circlip (4) from the key slot of the lock washer (3).
(b)
Hold the tail of the circlip (4) with a pair of thin-nose pliers.
(c)
Carefully pull the circlip (4) in a clockwise direction until it releases from the chamfered slot in the nut (2).
(14)
Remove the lock washer (3) from the nut (2).
(15)
Use the TUBE SPANNER (460005834) and remove the nut (2) and the washer (1) from the cardan joint (5).
(16)
Loosen the strap (but not fully) on the side-stay splint assembly.
(17)
Move the side-stay around the side-stay center-joint so that the cardan joint (5) comes out of the MLG attachment lug.
(18)
Remove the circlip (11) as follows: NOTE : Make sure that all the related parts are clean before you
____
remove the circlip (11).
(a)
Use an applicable tool to release the tail of the circlip (11) from the key slot of the lock washer (10).
(b)
Hold the tail of the circlip (11) with a pair of thin-nose pliers.
(c)
Carefully pull the circlip (11) in a clockwise direction until it releases from the chamfered slot in the nut (9).
(19)
Remove the lock washer (10) from the nut (9).
(20)
Use the TORQUE ADAPTOR (460005812) and remove the nut (9) and the washer (8) from the cardan joint (12).
(21)
Move the side-stay so that the cardan joint (12) comes out of the side-stay bracket. Tighten the strap to prevent movement of the side-stay assembly (6).
WARNING : BE CAREFUL WHEN YOU REMOVE OR INSTALL THE MLG SIDE-STAY. IT
_______
WEIGHS 62.5kg (137.5lb).
(a) Lower the side-stay assembly (6) on to a trestle and remove the cables from the hook.
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-16Page 423 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(22) If the side-stay assembly (6) is to be replaced, remove the side-stay
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(45)
