(Ref. Fig. 401/TASK 32-11-29-991-001) R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 32-11-29-991-001-B)
**ON A/C 001-003, 051-052,
Subtask 32-11-29-020-050
A. Removal of the Torque Link Damper WARNING : CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE
_______
LOCKWIRE CAN CUT OR BLIND YOU.
(1)
Remove and discard the cable tie (8). Remove the cover (7).
(2)
Remove and discard the cotter pin (15).
(3)
Remove the nut (14) and the bolt (16).
(4)
Hold the torque link pin (6) with the TORQUE REACTION ADAPTOR (460007242) and remove the nut (13) and the spacer (12).
(5)
Hold the bottom torque link assembly and remove:
-
the torque link pin (6)
-
the sleeve (11)
-
the spacer (10).
(6)
Carefully lower the bottom torque link assembly.
(7)
Remove and discard the lockwire from the bolts (1).
(8)
Remove the bolts (1) and the washers (2).
1EFF : ALL 1 32-11-29Page 403 1 1 Aug 01/05 1 1 1CES 1
Torque Link Damper - Location and Detail
Figure 401/TASK 32-11-29-991-001
R 1EFF : 001-003, 051-052, 1 32-11-29Page 404 1 1 May 01/05 1 1 1CES 1
Torque Link Damper - Location and Detail
Figure 401A/TASK 32-11-29-991-001-B
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-29Page 405 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 (9) Carefully remove the torque link damper (5).
(10) Remove the spacer (4), the spacer assembly (3) and the sleeve (9) from the top torque link assembly.
R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 32-11-29-020-050-B
A. Removal of the Torque Link Damper WARNING : CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE
_______
LOCKWIRE CAN CUT OR BLIND YOU.
(1)
Remove and discard the cable tie (4). Remove the cover (5).
(2)
Remove and discard the cotter pin (20).
(3)
Remove the nut (21), the washer (22) and the bolt (19).
(4)
Hold the torque link pin (3) with the TORQUE REACTION ADAPTOR (460007242) and remove the nut (18) and the spacer (17).
(5)
Hold the bottom torque link assembly and remove the torque link pin (3), the sleeve (16), the spacer (15) and the sleeve (7).
(6)
Carefully lower the bottom torque link assembly.
(7)
Remove and discard the lockwire from the bolts (9) and (10).
(8)
Remove the bolts (9) and the washers (8).
(9)
Remove the bolts (10) and the washers (11).
(10)
Remove the bolts (13), the washers (14) and the bracket (12).
(11)
Carefully remove the torque link damper (2).
(12)
Remove the spacer (1) and the shaped spacer (6).
1EFF : ALL 1 32-11-29Page 406 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
TASK 32-11-29-400-001
Installation of the Torque Link Damper 2823GM, 2824GM
WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : WHEN YOU DO A MAINTENANCE TASK THAT USES COMMON GREASE, USE ONLY
_______ GREASES OF THE SAME SPECIFICATION (IT IS PERMITTED TO USE DIFFERENT BRANDS IF THEIR SPECIFICATIONS ARE THE SAME). DO NOT MIX GREASES THAT HAVE CLAY THICKENERS WITH GREASES THAT HAVE LITHIUM THICKENERS. THIS MIXTURE CAN CHANGE THE LUBRICATION PROPERTIES OF THE GREASE. IF YOU USE GREASES OF DIFFERENT TYPES (SPECIALLY THOSE WITH CLAY THICKENERS AND LITHIUM THICKENERS), DECREASE THE SERVICE INTERVALS OF THE AIRCRAFT (BY HALF, FOR EXAMPLE) SPECIFIED IN THE MAINTENANCE PLANNING DOCUMENT. DO THIS FOR APPROXIMATELY THREE OR FOUR SERVICES (REFER TO YOUR IN-SERVICE DATA TO FIND THE NUMBER OF SERVICES BEST ADAPTED TO YOUR AIRCRAFT).
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊(cè) AMM LANDING GEAR 起落架2(107)
