(f)
TORQUE the locknut (71) to between 5.7 and 6.78 m.daN (42.03 and
49.99 lbf.ft).
(g)
Put the band-clamps (101), (103), (106), (108) and (110) in position and tighten the band-clamp nuts (102), (104), (105),
(107) and (110).
(h)
Examine the routings of the rigid hydraulic pipes for correct installation. Make sure that the pipes do not touch the MLG leg or each other.
(i)
Safety the band-clamp nuts (102), (104), (105), (107) and (110) with MISCELLANEOUS (Material No. 19-010).
(2)
To install the flexible hydraulic hoses, do the steps that follow: NOTE : When you install the flexible hoses, make sure that you do not
____
put kinks in them.
R 1EFF : 001-003, 051-052, 1 32-11-12Page 431 1 1 May 01/05 1 1 1CES 1
(a)
Put the flexible hose (67) in position and connect the union (74).
(b)
Put the flexible hose (68) in position and connect the union (73).
(c)
Put the flexible hose (29) in position and connect the union (32).
(d)
Put the flexible hose (30) in position and connect the union (31).
(e)
Put the flexible hose (12) in position and connect the unions
(13) and (85).
(f)
Put the flexible hose (11) in position and connect the unions
(10) and (84).
(g)
TORQUE the unions (74), (32), (31), (13), (10), (84) and (85) to between 2.4 and 2.8 m.daN (17.69 and 20.64 lbf.ft).
(h)
TORQUE the union (73) to between 4.79 and 5.23 m.daN (35.32 and
38.56 lbf.ft).
(i)
Put the blocks (41) and the channels (39) in position on the flexible hoses (11) and (12). Install them with the bolts (40), the washers (42) and the nuts (38).
(j)
TORQUE the nuts (38) to between 0.4 and 0.45 m.daN (35.39 and
39.82 lbf.in).
(k)
Put the line support block assembly (45) in position on the flexible hoses (11) and (12). Loosely install with the bolts (46), the washers (44) and the nuts (43).
(l)
Make sure that the dimension Y is 150 mm (5.91 in.).
(m)
TORQUE the nuts (43) to between 0.4 and 0.45 m.daN (35.39 and
39.82 lbf.in).
(n)
Put the flexible hose (27) in position and connect the unions
(28) and (82).
(o)
Put the flexible hose (26) in position and connect the unions
(25) and (81).
R 1EFF : 001-003, 051-052, 1 32-11-12Page 432 1 1 May 01/05 1 1 1CES 1
(p)
TORQUE the unions (28), (82), (25) and (81) to between 2.4 and
2.8 m.daN (17.69 and 20.64 lbf.ft).
(q)
Put the blocks (36) and the channels (33) in position on the flexible hoses (26) and (27). Install them with the bolts (37), the washers (35) and the nuts (34).
(r)
TORQUE the nuts (34) to between 0.4 and 0.45 m.daN (35.39 and
39.82 lbf.in).
(s)
Put the block assemblies (49) and the channels (51) in position on the flexible hoses (26) and (27). Install them with the bolts (50), the washers (48) and the nuts (47).
(t)
TORQUE the nuts (47) to between 0.4 and 0.45 m.daN (35.39 and
39.82 lbf.in).
(u)
Put the line support block assembly (53) in position on the
flexible hoses (26) and (27). Loosely install with the bolts
(52), the washers (55) and the nuts (54).
(v)
Make sure that the dimension Z is 280 mm (11.02 in.).
(w)
TORQUE the nuts (54) to between 0.4 and 0.45 m.daN (35.39 and
39.82 lbf.in).
(x)
Put the flexible hoses (21) and (24) in position and connect the unions (22) and (23).
(y)
TORQUE the unions (22) and (23) to between 2.4 and 2.8 m.daN
(17.69 and 20.64 lbf.ft).
(z)
Safety the unions (22) and (23) with MISCELLANEOUS (Material No. 19-010).
(aa) Put the line support block assemblies (20) in position on the flexible hoses (21), (24), (26) and (27). Loosely install the bolts (18), the washers (19) and (17) and the nuts (16).
(ab) Make sure that the dimension X is between 35 and 40 mm (1.38 and
1.57 in.).
(Ref. Fig. 406/TASK 32-11-12-991-010)
(ac) Tighten the nuts (16) and safety with a new cotter pin (15).
(ad) Put the flexible hoses (9) and (14) in position and connect the unions (7) and (8).
R 1EFF : 001-003, 051-052, 1 32-11-12Page 433 1 1 May 01/05 1 1 1CES 1
MLG Hydraulic Dressings - Location and Detail
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM LANDING GEAR 起落架2(7)
