-the total clearance must be between 0.043 mm (0.0016 in.) and
 0.143 mm (0.0056 in.). If the total clearance is less than
 0.043 mm (0.0016 in.) or more than 0.143 mm (0.0056 in.), do Para. (a) 1 thru 4.
 (17)
 Use a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean the mating surfaces of the cardan joint (7), the washer (8) and the nut (9).

 (18)
 Apply SPECIAL MATERIALS (Material No. 05-047) to the mating surfaces of the cardan joint (7), the washer (8) and the nut (9).

 (19)
 Align the key slot of the locking washer (10) with the chamfered slot of the nut (9) and install the locking washer (10). Make sure that the space between the locking washer (10) and the nut (9) is full of SPECIAL MATERIALS (Material No. 05-047).

 (20)
 Align the circlip (11) with the key slot of the locking washer (10) and the chamfered slot in the nut (9). Install the circlip (11) (in a counterclockwise direction) until the end of the circlip (11) engages in the key slot of the locking washer (10).

 (21)
 Use a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean the mating surfaces of the cardan joint (5), the washer (1) and the nut (2).

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-11-18Page 428 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 (22)
 Apply SPECIAL MATERIALS (Material No. 05-047) to the mating surfaces of the cardan joint (5), the washer (1) and the nut (2).

 (23)
 Align the key slot of the locking washer (3) with the chamfered slot of the nut (4) and install the locking washer (3). Make sure that the space between the locking washer (3) and the nut (2) is full of SPECIAL MATERIALS (Material No. 05-047).

 (24)
 Align the circlip (4) with the key slot of the locking washer (3) and the chamfered slot in the nut (2). Turn the circlip (4) (in a counterclockwise direction) until the end of the circlip (4) engages in the key slot of the locking washer (3).

 (25)
 Release the lockstay and put it in position on the side-stay (6).

 (26)
 Put the washers (12) between the attachment of the lockstay and the lugs of the center joint of the side-stay (6).

 (27)
 Install the lockstay with the pin (21), the washers (22) and (13) and the nut (15).

 (28)
 TORQUE the nut (15) to between 1.5 and 2.26 m.daN (11.06 and 16.66 lbf.ft).

 (29)
 Safety the nut (15) with a new cotter pin (14).

 (30)
 Put the washers (19) between the lockspring link and the lockstay attachment lug.

 (31)
 Install the pin (20), the washer (18) and the nut (16).

 (32)
 TORQUE the nut (16) to between 0.34 and 0.508 m.daN (30.08 and 44.95 lbf.in).

 (33)
 Safety the nut (16) with a new cotter pin (17).

 (34)
 Remove the blanking caps from the electrical dressings and the proximity switches.

 (35)
 Install the lockstay actuating cylinder (Ref. TASK 32-11-21-400-001).

 (36)
 Install the lock springs (Ref. TASK 32-11-19-400-001).

 (37)
 Do the dimensional check of the proximity sensors on the side stay (Ref. TASK 32-31-73-200-001).

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-11-18Page 429 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 1EFF : ALL 1 32-11-18Page 430 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 32-11-18Page 431 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 32-11-18Page 432 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 32-11-18Page 433 1 1 May 01/04 1 1 1CES 1 1EFF : 301-399, 1 32-11-18Page 434 1 1 May 01/04 1 1 1CES 1 1EFF : ALL 1 32-11-18Page 435 1 1 May 01/04 1 1 1CES 1 Subtask 32-11-18-860-052

 (38) Do the detailed dimensional check of the MLG lockstay assembly (Ref. TASK 32-11-00-220-003).
 (39) Apply SEALANTS (Material No. 09-016) to: - the ends of the cardan joints (5) and (7) - the ends of the pins (20) and (21) - the nuts (2), (9), (15) and (16) - the washers (1), (8), (13), (18) and (22) - the locking washers (3) and (10).
 NOTE : Do not apply sealant between the washer (1) and the flanged____ bush of the side-stay assembly.
 (40) Lubricate the side-stay (6) through the greasers (Ref. TASK 12-22-32-640-001). 
R  **ON A/C 301-399, 
R  Subtask 32-11-18-420-054-A 
R  A. Preparation for Installation 
R R R R R R  (1) If the MLG side-stay has been replaced, install the HOIST (98D32104013004) on the side-stay (6) with: - the cables to the wing surface - the strap to the wing surface - the center joint of the side-stay (6) located in the center hole of the HOIST. 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(71)