WARNING : CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE
_______
LOCKWIRE CAN CUT OR BLIND YOU.
(1)
Remove and discard the lockwire from the locknuts (4) and (6).
(2)
Loosen the upper locknuts (6) to release the 1M and 2M harnesses from the brackets (5).
(3)
Loosen the upper locknut (4) to release the 2M harness from the bracket (3).
(Ref. Fig. 402A/TASK 32-11-43-991-037-B)
(4)
Remove the nuts (17), the washers (15) and the bolts (14) to release the P clips (16).
(Ref. Fig. 403A/TASK 32-11-43-991-002-A)
(5)
Loosen the band-clamp screws (32) sufficiently to remove the band-clamps (33) from the line-support blocks.
NOTE : When the band-clamps (33) are removed, make sure that the
____ mystic tape and the line-support blocks stay in position on the harnesses.
(6)
Carefully remove the band-clamps (33) from the leg assembly.
(7)
Remove and discard the cotter pins (38).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-11-43Page 420 1208-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(8)
Remove the nuts (37), the washers (36) and the bolts (34) to release the channels (35).
(9)
Remove the nuts (39), the washers (40) and the bolts (42) to release the clamps (41). Remove the clamp-blocks (43) from the harnesses.
**ON A/C 201-207,
Subtask 32-11-43-020-058-B
A. Preparation for Removal of the 1M and 2M Harnesses
(Ref. Fig. 401A/TASK 32-11-43-991-001-A)
WARNING : CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE
_______
LOCKWIRE CAN CUT OR BLIND YOU.
(1)
Remove and discard the lockwire from the locknuts (4) and (6).
(2)
Loosen the upper locknuts (6) to release the 1M and 2M harnesses from the brackets (5).
(3)
Loosen the upper locknut (4) to release the 2M harness from the bracket (3).
CAUTION : DO NOT REMOVE THE NUT, WASHER AND BOLT THAT HOLD THE TWO
_______ P-CLIPS TOGETHER (ADJACENT TO THE NORMAL BRAKE MANIFOLD). THIS WILL PREVENT AN INCORRECT ASSEMBLY DURING THE INSTALLATION PROCEDURE.
(Ref. Fig. 402A/TASK 32-11-43-991-037-B, 407/TASK 32-11-43-991-038)
(4)
Remove the nuts (17), the washers (15) and the bolts (14) to release the P clips (16). (Ref. Fig. 403A/TASK 32-11-43-991-002-A)
(5)
Loosen the band-clamp screws (32) sufficiently to remove the band-clamps (33) from the line-support blocks.
NOTE : When the band-clamps (33) are removed, make sure that the
____ mystic tape and the line-support blocks stay in position on the harnesses.
(6)
Carefully remove the band-clamps (33) from the leg assembly.
(7)
Remove and discard the cotter pins (38).
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-43Page 421 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
MLG Harnesses 1M and 2M - Location and Detail
Figure 407/TASK 32-11-43-991-038
R 1EFF : 201-207, 1 32-11-43Page 422 1 1 Nov 01/04 1 1 1CES 1
(8) Remove the nuts (37), the washers (36) and the bolts (34) to release the channels (35).
(9) Remove the nuts (39), the washers (40) and the bolts (42) to release the clamps (41). Remove the clamp-blocks (43) from the harnesses.
R **ON A/C 001-003, 051-052,
Subtask 32-11-43-020-061
B. Removal of the 1M and 2M Harnesses from the MLG Leg
CAUTION : MAKE SURE THAT ALL ELECTRICAL CONNECTORS ARE IDENTIFIED WITH_______ THEIR FIN NO. TO CORRECTLY CONNECT EACH PLUG TO ITS RELATED RECEPTACLE. INCORRECT CONNECTION OF THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO THE AIRCRAFT ELECTRICAL SYSTEM.
(1) For the 1M harness: (Ref. Fig. 401/TASK 32-11-43-991-001)
(a) Disconnect the electrical connector 4027VC (4028VC) (2) from the MLG disconnection box (Ref. TASK 32-11-46-000-001).
(Ref. Fig. 404/TASK 32-11-43-991-003)
(b) Remove the nuts (53), the washers (52) and the bolts (50) to release the cable support (51) from the bracket (54).
(Ref. Fig. 401/TASK 32-11-43-991-001)
R **ON A/C 001-002, 051-052,
(Ref. Fig. 405/TASK 32-11-43-991-004)
R **ON A/C 001-003, 051-052,
R Post SB 32-1190 For A/C 001-002,051-052,
(Ref. Fig. 405B/TASK 32-11-43-991-004-D)
R **ON A/C 001-003, 051-052,
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(113)
