R 1EFF : 301-399, 1 32-11-18Page 416 1 1 May 01/04 1 1 1CES 1
R (7) Tighten the strap and connect the cables to the hook. Tighten the
R cable.
R (8) Remove and discard the lockwire from the bolts (11). Remove the bolts
R (11) and the washers (10).
R (9) Use the TUBE SPANNER (460007272) to remove the nut (8) from the
R cardan joint (7).
R (10) Loosen the strap (but not fully) on the HOIST.
R (11) Move the side-stay (6) around the side-stay center joint so that the
R cardan joint (7) comes out of the MLG attachment lugs.
R NOTE : Before you remove the circlip (4), make sure that all the____
R related parts are clean.
R (12) Remove the circlip (4) as follows:
R (a) Use an applicable tool to release the tail of the circlip (4)
R from the key slot of the locking washer (3).
R (b) Hold the tail of the circlip (4) with a pair of thin nose pliers.
R (c) Carefully pull the circlip (4) (in a clockwise direction) until
R it releases from the chamfered slot in the nut (2).
R (13) Remove the locking washer (3) from the nut (2).
R (14) Use the TORQUE ADAPTOR (460005812) to remove the nut (2) and remove
R the washer (1) from the cardan joint (5).
R (a) Move the side-stay (6) so that the cardan joint (5) comes out of
R the side-stay bracket. Tighten the strap to prevent movement of
R the side-stay (6).
R (b) Lower the side-stay (6) on to the trestle and disconnect the
R cables from the hook.
R (15) If you are to replace the side-stay (6), remove the HOIST.
R (Ref. Fig. 403A/TASK 32-11-18-991-004-A)
R (16) Remove the seal (32) from the bush (33). Discard the seal (32).
R 1EFF : 301-399, 1 32-11-18Page 417 1 1 May 01/04 1 1 1CES 1
**ON A/C ALL
TASK 32-11-18-400-001
Installation of the MLG Side-Stay
WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : WHEN YOU DO A MAINTENANCE TASK THAT USES COMMON GREASE, USE ONLY
_______ GREASES OF THE SAME SPECIFICATION (IT IS PERMITTED TO USE DIFFERENT BRANDS IF THEIR SPECIFICATIONS ARE THE SAME). DO NOT MIX GREASES THAT HAVE CLAY THICKENERS WITH GREASES THAT HAVE LITHIUM THICKENERS. THIS MIXTURE CAN CHANGE THE LUBRICATION PROPERTIES OF THE GREASE. IF YOU USE GREASES OF DIFFERENT TYPES (SPECIALLY THOSE WITH CLAY THICKENERS AND LITHIUM THICKENERS), DECREASE THE SERVICE INTERVALS OF THE AIRCRAFT (BY HALF, FOR EXAMPLE) SPECIFIED IN THE MAINTENANCE PLANNING DOCUMENT. DO THIS FOR APPROXIMATELY THREE OR FOUR SERVICES (REFER TO YOUR IN-SERVICE DATA TO FIND THE NUMBER OF SERVICES BEST ADAPTED TO YOUR AIRCRAFT).
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific feeler gage
No specific safety barriers
No specific warning notice
No specific access platform 2.5 m (8 ft. 2 in.)
No specific access platform 3.0 m (9 ft. 10 in.)
R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
1EFF : ALL 1 32-11-18Page 418 1 1 May 01/05 1 1 1CES 1 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific Torque Wrench : range 2.00 to 20.00 m.daN
(15.00 to 150.00 lbf.ft)
No specific Torque Wrench : range 6.00 to 36.00 m.daN
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(67)
