Adjustment of the Door Stop Fittings of the FWD Passenger/Crew Door
Figure 501/TASK 52-11-00-991-019
R 1EFF : ALL 1 52-11-00Page 510 1 1 May 01/05 1 1 1CES 1
Adjustment of the Upper and Lower Guide Fittings of the FWD Passenger/Crew Door Figure 502/TASK 52-11-00-991-005
R 1EFF : 001-049, 051-056, 1 52-11-00Page 511 1 1 May 01/05 1 1 1CES 1
Adjustment of the Upper and Lower Guide Fittings of the FWD Passenger/Crew Door Figure 502A/TASK 52-11-00-991-005-A
R 1EFF : 057-099, 101-149, 151-199, 201-299, 1 52-11-00Page 512 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Adjustment of the Girt Bar and Load on the Inner Control Handle of the FWD
Passenger/Crew Door
Figure 503/TASK 52-11-00-991-006
R 1EFF : 001-002, 051-052, 1 52-11-00Page 513 1 1 May 01/05 1 1 1CES 1
Adjustment of the Girt Bar and Load on the Inner Control Handle of the FWD Passenger/Crew Door Figure 503A/TASK 52-11-00-991-006-A
1EFF : ALL 1 52-11-00Page 514 1 1 May 01/05R 1 1 1CES 1
(c) Close the door.
(5)
Open the door. Make sure that when you start to open the door (during door lifting travel), the clearance F3 (between the telescopic fork
(2) ends and thegirt bar fittings (1)) is 5 mm (0.1968 in.) minimum.
(6)
If the clearance F3 is not in the tolerances, adjust the girt bar fittings as follows: (Ref. Fig. 504/TASK 52-11-00-991-017)
(a)
Loosen the screws (91), (96) of the girt bar fittings (92), (95).
(b)
Remove the sealant around the girt bar fittings (92), (95) and on the heads of the screws (91), (96). Use a CLEANING AGENTS (Material No. 11-004) with a MISCELLANEOUS (Material No. 19-003).
(c)
Identify the position of the serrations of the girt bar fittings (92), (95) and the plates (93) and (94).
(d)
Move the girt bar fittings from the serrations on the X and Y axes to get correct clearance.
R **ON A/C 057-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-11-00-820-050-A
A. Adjustment of the Door during Opening and Closing (Ref. Fig. 501/TASK 52-11-00-991-019, 502A/TASK 52-11-00-991-005-A, 503A/TASK 52-11-00-991-006-A)
(1)
Make sure that when you start to open the door, the clearance H1 (between the door stops (21) and the door frame stops (22)) is 5 mm (0.1968 in.) minimum.
(2)
Slowly close the door and make sure that there is no hard point (between the door stops (21) and the door frame stops (22)) for the overlap H3 of 3 mm (0.1181 in.) to 4 mm (0.1574 in.).
(3)
The clearance H2 must be 0.2 mm (0.0078 in.) minimum, the guide rollers (31) touch the guide fittings (32) and (36).
1EFF : ALL 1 52-11-00Page 515 1 1 Aug 01/05 1 1 1CES 1
Adjustment of the Girt Bar Fittings of the FWD Passenger/Crew Door
Figure 504/TASK 52-11-00-991-017
R 1EFF : ALL 1 52-11-00Page 516 1 1 May 01/05 1 1 1CES 1
(4)
If the clearance H2 is not in the tolerances, adjust the upper and lower guide fittings (32) and (36) as follows:
(a)
Open the door and identify the position of the serration plates
(37) and (38) and of the upper and lower guide fittings (32), (36).
(b)
Loosen the screws (40) and move the guide fittings (32), (36) to get the clearance H2.
(c)
Make sure that the eccentric washers (39):
-fully seal the holes of the guide fittings (32) and (36),
-
are not above the rounded areas or spot-facing edges,
-
are not out of the outer contour of the fitting.
(d)
Temporarily tighten the screws (40).
