(2)
 Make sure that the door lining and the insulation are removed.

 (3)
 Obey the special precautions before you start work on the door (Ref. TASK 52-10-00-860-001).

 Subtask 52-11-21-865-058
 B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
 Subtask 52-11-21-110-050
 C. Cleaning
 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE SPECIAL
_______
 MATERIAL.
 THIS MATERIAL IS DANGEROUS.

 (1) Clean the component interface and/or the adjacent area.
 1EFF : ALL 1 52-11-21Page 440 1 1 Feb 01/02R 1 1 1CES 1

 (2)
 If necessary, clean the components with CLEANING AGENTS (Material No. 11-004) and MISCELLANEOUS (Material No. 19-003).

 (3)
 Do an inspection of the component interface and/or the adjacent area.

 (4)
 Make sure that the parts retained from the removed component are clean and in the correct condition. (Ref. TASK 52-11-21-220-001)

 4. Procedure
_________
 Subtask 52-11-21-420-050

 A. Installation of the Inner Control Handle
 (Ref. Fig. 404/TASK 52-11-21-991-007)

 (1)
 Apply COMMON GREASE (Material No. 04-004) on the axle (174) of the gearbox.

 (2)
 Put the inner control handle (173) in position on the axle (174). Make sure that the grooves are aligned.

 (3)
 Install the washer (170) and the nut (172).

 (4)
 TORQUE the nut (172) to between 0.2 and 0.4 m.daN (17.69 and 35.39 lbf.in).

 (5)
 Install a new cotter pin (171). NOTE : If you must install a new axle (174), drill a hole of dia. 3

____ mm (0.1181 in.) for the cotter pin installation.

 (6)
 Adjustment of the inner control handle.
 (Ref. Fig. 413/TASK 52-11-21-991-010)

 (a)
 Put the inner control handle in the door-down position.

 (b)
 Remove the lockwire from the nut (254) and adjust the length of the eye bolt (251) until:

R  1_The bellcrank (252) touches the stop (253). 2 The position X1 is 41 +1 -1 mm (1.6141 +0.0393 -0.0393 in.)
_ when the inner control handle is in the fully down position.
 (c) TORQUE the nut (254) to between 0.6 and 0.7 m.daN (53.09 and
 61.94 lbf.in).
 1EFF : ALL 1 52-11-21Page 441 1 1 Feb 01/03 1 1 1CES 1

 Inner and Outer Control Handles - Gearbox Adjustment Figure 413/TASK 52-11-21-991-010- 13 (SHEET 1)
 1EFF : ALL 1 52-11-21Page 442 1 1 Feb 01/02R 1 1 1CES 1

 Inner and Outer Control Handles - Gearbox Adjustment Figure 413/TASK 52-11-21-991-010- 23 (SHEET 2)
 1EFF : ALL 1 52-11-21Page 443 1 1 Feb 01/02R 1 1 1CES 1

 Inner and Outer Control Handles - Gearbox Adjustment Figure 413/TASK 52-11-21-991-010- 33 (SHEET 3)
 1EFF : ALL 1 52-11-21Page 444 1 1 Feb 01/02R 1 1 1CES 1

 (d)
 Safety the nut (254) with MISCELLANEOUS (Material No. 19-010).

 (e)
 Make sure that the clearance J1 is 1 -0 +0.5 mm (0.0393 -0.0000 +0.0196 in.).

 (f)
 If the clearance J1 is not in the tolerances, do the adjustment below:

 1 Adjust the thickness of the washers (257) and (259) so that it
_ is not necessary to adjust the length of the spring (258).
 (7) Adjustment of the friction point of the inner control handle. (Ref. Fig. 413/TASK 52-11-21-991-010)
 (a)
 Put the stop assembly (260) in position and make sure that, in relation to the ramp (262):

 -
the clearance J3 is 0.5 mm (0.0196 in.) minimum.

 -
the ball goes into the ramp by 0.3 mm (0.0118 in.) to 0.5 mm (0.0196 in.).

 -
the clearance J7 is 4 -0.2 +0.2 mm (0.1574 -0.0078 +0.0078 in.).

 (b)
 Adjust the screw (261) so that the force necessary to lock the inner control handle is 10 daN (22.4808 lbf) (friction point plus normal operation force).
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門1(174)