R  **ON A/C 001-002, 
R  TASK 52-10-00-080-001 
R  Removal of the Passenger/Crew Door Ballast Weight (98D52103501000) for Escape 
R  Slide 
R  1. Reason for the Job__________________ 
R  This procedure tells how to remove the ballast weight set to 33 kg (72.752 
R  lb) which is equal to the weight of the escape slide, the door linings and 
R  the door insulation. 
R  2. Job Set-up Information______________________ 
R  A. Fixtures, Tools, Test and Support Equipment 
R  -------------------------------------------------------------------------------
R  REFERENCE QTY DESIGNATION 
R  -------------------------------------------------------------------------------
R  No specific access platform 3.5 m (11 ft. 6 in.) 
R  98D52103501000 1 BALLAST WEIGHT - PASSENGER CREW DOOR 
R  B. Referenced Information 
R  -------------------------------------------------------------------------------
R  REFERENCE DESIGNATION 
R  -------------------------------------------------------------------------------
R  52-10-00-860-001 Special Precautions before Work on the Passenger/Crew 
R  Door 
R  52-10-00-991-049 Fig. 205 
R  3. Job Set-up__________ 
R  Subtask 52-10-00-860-054 
R  A. Aircraft Maintenance Configuration 
R  (1) Make sure that the access platform is in position at the zone 831 or 
R  841 or 832 or 842. 
R  (2) Obey the special precautions before you start work on the door 
R  (Ref. TASK 52-10-00-860-001).

R  Subtask 52-10-00-865-089 
R  B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and 
R  tagged 
R  -------------------------------------------------------------------------------
R  PANEL  DESIGNATION  IDENT. LOCATION 
R  -------------------------------------------------------------------------------
R  121VU EIS/SLIDES/ARM AND WARN/FLT  15WN  P11 
R  121VU EIS/SLIDES/ARM AND WARN/GND  13WN  P10 
R  121VU EIS/SDAC1 AND 2/DOOR/DET/PAX  48WV  P05 
R  4. Procedure_________ 
R  Subtask 52-10-00-080-050 
R  A. Removal of the Ballast Weight 
R  (Ref. Fig. 205/TASK 52-10-00-991-049) 
R  (1) Remove the BALLAST WEIGHT - PASSENGER CREW DOOR (98D52103501000) as 
R  follows: 
R  (a) Remove the weight assy with the weight N2 as follows: 
R  1_  Unscrew the nut (3) and remove it.
R  2_  Remove the pin (6) and the weight N2 (5).
R  (b) Remove the base plate with the weight fitting from the door as 
R  follows: 
R  1_  Remove the pins (4).
R  2_  Lift the base plate (2) with the weight fitting (1) and remove
R  it from the door. 
R  NOTE : Two persons are necessary for this step, one on each____ 
R  side of the base plate (2). The base plate (2) with the 
R  weight fitting (1) weighs 23 kg (50.705 lb).

 1EFF : 001-002, 1 52-10-00Page 220 1 1 Feb 01/02 1 1 1CES 1R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,

 TASK 52-10-00-080-001-A
 Removal of the Passenger/Crew Door Ballast Weight (98D52103501000) for Escape Slide/Raft
 1. Reason for the Job
__________________
 This procedure tells how to remove the ballast weight set to 60 kg (132.277 lb) which is equal to the weight of the escape slide/raft, the door linings and the door insulation.
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE  QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific access platform 3.5 m (11 ft. 6 in.)
 98D52103501000 1 BALLAST WEIGHT - PASSENGER CREW DOOR

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
52-10-00-860-001  Special Precautions before Work on the Passenger/Crew Door 52-10-00-991-049-A Fig. 205A
 3. Job Set-up
__________
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門1(72)