(e)
Close the door.
(5)
Open the door. Make sure that when you start to open the door (during door lifting travel), the clearance F3 (between the telescopic fork
(2) ends and the girt bar fittings (1)) is 5 mm (0.1968 in.) minimum.
(6)
If the clearance F3 is not in the tolerances, adjust the girt bar fittings as follows: (Ref. Fig. 504/TASK 52-11-00-991-017)
(a)
Loosen the screws (91), (96) of the girt bar fittings (92), (95).
(b)
Remove the sealant around the girt bar fittings (92), (95) and on the heads of the screws (91), (96). Use a CLEANING AGENTS (Material No. 11-004) with a MISCELLANEOUS (Material No. 19-003).
(c)
Identify the position of the serrations of the girt bar fittings (92), (95) and the plates (93) and (94).
(d)
Move the girt bar fittings from the serrations on the X and Y axes to get correct clearance.
R 1EFF : 057-099, 101-149, 151-199, 201-299, 1 52-11-00Page 517 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
**ON A/C ALL
Subtask 52-11-00-820-052
B. Adjustment of the Door in the Down Position (Ref. Fig. 505/TASK 52-11-00-991-001, 506/TASK 52-11-00-991-003, 507/TASK 52-11-00-991-018)
(1)
Install two positioning templates on the X axis, on the door frame.
(a)
Install one template between the longerons L5 and L6.
(b)
Install the other template between the longerons L2 and L3.
(2)
If the templates do not touch the door frame or the door contour, adjust the door on the X axis as follows:
(a)
Close and lock the door.
(b)
Disconnect the upper and lower connection links (11) from each side of the yoke.
(c)
Remove and discard the cotter pin (13).
(d)
Remove the nuts (14), the washers (15) and the bolts (16) to disconnect the upper and lower connection links (11).
(e)
Adjust the door on the X axis with washers (12) of a different thickness.
(f)
Make sure that the clearance B is less than or equal to 0.1 mm (0.0039 in.).
NOTE : The thickness of the two washers (12) at level of the
____ lower and upper connection links (11) is equal to the nominal thickness. The clearance B must be in the tolerances.
(g)
Connect the upper and lower connection links (11).
(h)
Install the washers (15), the bolts (16).
(i)
Install the nuts (14).
(j)
TORQUE the nuts (14) to between 1.2 and 1.35 m.daN (106.19 and
119.46 lbf.in).
1EFF : ALL 1 52-11-00Page 518 1 1 May 01/05R 1 1 1CES 1
INTENTIONALLY BLANK
R 1 1
52-11-00Page 519
1 1 May 01/05 1 1 1CES 1
Adjustment on the X axis of the FWD Passenger/Crew Door Figure 505/TASK 52-11-00-991-001- 13 (SHEET 1)
1EFF : ALL 1 52-11-00Page 520 1 1 May 01/05R 1 1 1CES 1
Adjustment on the X axis of the FWD Passenger/Crew Door Figure 505/TASK 52-11-00-991-001- 23 (SHEET 2)
1EFF : ALL 1 52-11-00Page 521 1 1 May 01/05R 1 1 1CES 1
Adjustment on the X axis of the FWD Passenger/Crew Door Figure 505/TASK 52-11-00-991-001- 33 (SHEET 3)
1EFF : ALL 1 52-11-00Page 522 1 1 May 01/05R 1 1 1CES 1
Adjustment of the Y Axis and Stops of the FWD Passenger/Crew Door Figure 506/TASK 52-11-00-991-003
1EFF : ALL 1 52-11-00Page 523 1 1 May 01/05R 1 1 1CES 1
Clearances - Adjustment on Z Axis of the FWD Passenger/Crew Door Figure 507/TASK 52-11-00-991-018
1EFF : ALL 1 52-11-00Page 524 1 1 May 01/05R 1 1 1CES 1
(3)
Make sure that the clearance E8 is 70 +0.7 -0.7 mm (2.7559 +0.0275 -0.0275 in.).
(4)
Do a check of the peripheral clearance between the door and the door frame:
(a)
At FR16, E1 is 4 +1 -1 mm (0.1574 +0.0393 -0.0393 in.).
(b)
At FR20, E2 is 4 +1.8 -1.8 mm (0.1574 +0.0708 -0.0708 in.). NOTE : A clearance of 4 +2.2 -2.2 mm (0.1574 +0.0866 -0.0866 in.)
____ is permitted on the rear part for a maximum length of 400 mm (15.7480 in.). This maximum total length can be the addition of smaller lengths at a maximum of three locations.
(c)
E3 is 4 +1.5 -2.5 mm (0.1574 +0.0590 -0.0984 in.).
(5)
Do a check of the flushness between the door and the door frame at door stop levels L1 to L7.
(a) E5 is 1.5 +1 -1 mm (0.0590 +0.0393 -0.0393 in.). NOTE : A clearance of 1.5 +1.3 -1.3 mm (0.0590 +0.0511 -0.0511
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門1(114)
