WARNING : STOP THE OPENING PROCEDURE IF THE RED WARNING LIGHT FLASHES.
_______ RESIDUAL PRESSURE COULD CAUSE THE DOOR TO OPEN WITH A SUDDEN FORCE AND INJURE PERSONS AND/OR DAMAGE THE AIRCRAFT.
(1)
Put the access platform in position at the applicable zone 831 or 841 or 832 or 842.
(2)
Open the applicable passenger/crew door 831, 841 or 832, 842 (Ref. TASK 52-10-00-010-001).
(3)
Obey the special precautions before you start work on the door. (Ref. TASK 52-10-00-860-001)
4. Procedure
_________ Subtask 52-10-00-410-066
A. Closing of the Door
(1) Close the door from the inside.
1EFF : ALL 1 52-10-00Page 538 1 1 May 01/04R 1 1 1CES 1
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,
Subtask 52-10-00-081-051
B. Removal of the Safety Pin
(1)
Remove the SAFETY PIN - SLIDE ARMING (98D52103500000) from the emergency control handle.
(2)
Put the emergency control handle in the ARMED position.
R **ON A/C 102-149, 201-207, 211-299, 301-399, 401-499, Post SB 25-1270 For A/C 102-105,201-207, Subtask 52-10-00-081-051-A
B. Removal of the Safety Pin
(1)
Open the protection cover to get access to the emergency control handle.
(2)
Remove the SAFETY PIN - SLIDE ARMING (98D52103500000) from the emergency control handle.
(3) Put the emergency control handle in the ARMED position.
**ON A/C ALL
Subtask 52-10-00-720-057
C. Functional Test of the Release Mechanism of the Emergency Escape Slide **ON A/C 001-002,
(Ref. Fig. 505/TASK 52-10-00-991-016)
**ON A/C 003-049, 051-099, 101-105, 151-158, 201-210,
(Ref. Fig. 505A/TASK 52-10-00-991-016-B)
1EFF : ALL 1 52-10-00Page 539 1 1 Aug 01/05 1 1 1CES 1
ARMED/DISARMED Position of the Girt Bar
Figure 505/TASK 52-10-00-991-016
R 1EFF : 001-002, 1 52-10-00 Page 540
1 1 May 01/04
1 1
1CES 1
ARMED/DISARMED Position of the Girt Bar Figure 505A/TASK 52-10-00-991-016-B
R 1EFF : 003-049, 051-099, 101-105, 151-158, 1 52-10-00Page 541 1201-210, 1May 01/05 1 1 1CES 1R **ON A/C 106-149, 159-199, 211-299, 301-399, 401-499,
(Ref. Fig. 505B/TASK 52-10-00-991-016-C)
**ON A/C ALL
(1)
Make sure that the girt bar is in the ARMED position and make sure that the mechanism operates correctly. The visual indicator comes into view. It moves to the position shown by the arrow on the placard installed on the floor.
(2)
Put the emergency control handle in the DISARMED position.
(3)
Make sure that the girt bar is in the DISARMED position. The visual indicator comes out of view. It moves away from the arrow.
Subtask 52-10-00-220-058
D. Check of the Load of the Emergency Control Handle
(1) With a dynamometer make sure that the load necessary to move from the DISARMED position to the ARMED position is less than or equal to 10 daN (22.4808 lbf).
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,
Subtask 52-10-00-481-051
E. Installation of the Safety Pin
(1)
Put the emergency control handle in the DISARMED position.
(2)
Install the SAFETY PIN - SLIDE ARMING (98D52103500000) on the emergency control handle.
1EFF : ALL 1 52-10-00Page 542 1 1 Aug 01/05 1 1 1CES 1
ARMED/DISARMED Position of the Girt Bar Figure 505B/TASK 52-10-00-991-016-C
R 1EFF : 106-149, 159-199, 211-299, 301-399, 1 52-10-00Page 543 1401-499, 1Aug 01/05 1 1 1CES 1
R **ON A/C 102-149, 201-207, 211-299, 301-399, 401-499, Post SB 25-1270 For A/C 102-105,201-207, Subtask 52-10-00-481-051-A
E. Installation of the Safety Pin
(1)
Put the emergency control handle in the DISARMED position.
(2)
Install the SAFETY PIN - SLIDE ARMING (98D52103500000) on the emergency control handle.
(3) Close the protection cover to the emergency control handle.
**ON A/C ALL
5. Close-up
________
Subtask 52-10-00-410-068
A. Close Access
(1)
Obey the special precautions after the work on the door. (Ref. TASK 52-10-00-860-002)
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Close the passenger/crew door 831, 841 or 832, 842 (Ref. TASK 52-10-00-410-001).
(4)
Remove the access platform(s).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門1(96)
