(2)
 Make sure that the clearance K2 between the telescopic rod (41) and the fitting (42) is 1.5 mm (0.0590 in.) minimum.

 Subtask 52-11-11-820-060
 R. Check and Adjustment of the Compensation Mechanism
 (1) Do a check and adjustment of the compensation mechanism (Ref. TASK 52-11-00-820-002).
 Subtask 52-11-11-220-050
 S. Check of the Outer Control Handle Locking
 (Ref. Fig. 416/TASK 52-11-11-991-002)

 (1)
 Open the door from the outside and close the door from the inside.

 (2)
 Make sure that the handle flap (704) comes back to its initial position when you close the door from the outside.

 (3)
 Apply a manual pressure on the handle flap (704) until it touches the stop (703). Release the handle flap and make sure that the handle flap (704) goes back to its initial position.

 NOTE : Repeat this procedure five times.
____
 (4) If necessary, adjust the handle flap (704) as follows:
 (a)
 Loosen the screw (701), remove the stop (703) and the adjustable shim (702).

 (b)
 Adjust the adjustable shim (702) to get the correct position of the handle flap (704) when the handle is in the closed position.

 (c)
 Install the stop (703) with the adjustable shim (702) and the screw (701).

 (d)
 Tighten the screw (701).

 1EFF : ALL 1 52-11-11Page 456 1 1 Feb 01/04R 1 1 1CES 1

 Adjustment of the Door-Damper and Emergency-Operation Cylinder
 Figure 415/TASK 52-11-11-991-018

 1EFF : ALL 1 52-11-11Page 457 1 1 Feb 01/04R 1 1 1CES 1

 Adjustment of the Outer Control Handle
 Figure 416/TASK 52-11-11-991-002
 1EFF :  ALL  1  52-11-11 Page 458 
1  1  Feb 01/04
 1  1
 1CES  1

 (e) Repeat step (3). Subtask 52-11-11-820-065
 T. Check of the Emergency Escape-Slide Control-Handle Disarming
 (1)
 Close the door.

 (2)
 Put the emergency control handle in the ARMED position.

 (3)
 Open the door from the outside.

 (4)
 Make sure that the emergency escape slide moves to the DISARMED position.

 Subtask 52-11-11-820-061
 U. Check of the Door Locking in the Up Position
 (Ref. Fig. 417/TASK 52-11-11-991-016)

 (1)
 Make sure that during the opening of the door, the handle locks before release of the rollers from the guide fittings.

 (2)
 Make sure that when you close the door with the inner control handle

 (805) you feel no hard points caused by the non-retraction of the hook (804).

 (3)
 If necessary, do the adjustement below:

 (a)
 Remove the lockwire from the nuts (801) and (803) and discard it.

 (b)
 Decrease the rod length (802) so that when you close the door, there is no hard point caused by the non-retraction of the hook

 (804) with the door in the up position.

 (c)
 Tighten the nuts (801) and (803) and safety them with MISCELLANEOUS (Material No. 19-010).

 (d)
 Open the door in the up position and make sure that you can correctly install the RIGGING PIN (98DNSA20206120).

 (4)
 If you still feel the hard point apply COMMON GREASE (Material No. 04-004) on the contact surface of the hook (804) with the handle (405).

 1EFF : ALL 1 52-11-11Page 459 1 1 Feb 01/04 1 1 1CES 1

 Adjustment of the Inner Control Handle
 Figure 417/TASK 52-11-11-991-016
 1EFF :  ALL  1  52-11-11 Page 460 
1  1  Feb 01/04
 1  1
 1CES  1

 Subtask 52-11-11-820-062
 V. Check of Preload of the Cover Plate
 (1) Do a check of the preload of the cover plate (Ref. TASK 52-10-00-220-007).
 NOTE : Do this check only after the replacement of the door by a new____ door.
 NOTE : After adjustment of the door, you can posibly see a permitted____ bend line on the cover plate.
 Subtask 52-11-11-820-068
 W. Check and Adjustment of the Proximity Switch
 (1) Do the adjustment of the proximity switch 11WV1 or 11WV2 of the door locking mechanism (Ref. TASK 52-71-00-820-001).
 5. Close-up________
 Subtask 52-11-11-865-051
 A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 13WN, 15WN, 48WV
 **ON A/C 001-002,
 Subtask 52-11-11-410-051
 B. Installation of the Component 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門1(142)