(2)
Carefully degrease the chafing area with CLEANING AGENTS (Material No. 11-004) and a lint-free cloth.
(3)
Apply a thin layer of BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) to the chafing area and make it smooth with a spatula.
(4)
Make sure that dust does not touch the chafing area. Let the adhesive dry between 10 hours and 12 hours.
1EFF : ALL 1 52-11-18Page 803 1 1 Feb 01/98 1 1 1CES 1
Wooden Bonding Block
Figure 801/TASK 52-11-18-991-002
1EFF : ALL 1 52-11-18 Page 804
1 1 Feb 01/98
1 1
1CES 1
Wooden Bonding Block
Figure 802/TASK 52-11-18-991-003
1EFF : ALL 1 52-11-18 Page 805
1 1 Feb 01/98
1 1
1CES 1
Repair of Damage
Figure 803/TASK 52-11-18-991-004
1EFF : ALL 1 52-11-18 Page 806
1 1 Feb 01/98
1 1
1CES 1
Repair of Damage
Figure 804/TASK 52-11-18-991-005
1EFF : ALL 1 52-11-18 Page 807
1 1 Feb 01/98
1 1
1CES 1
Subtask 52-11-18-340-051
B. Repair the Cuts with a small Depth (not more than one third of the
thickness of the seal).
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1)
Lightly rub the cut area with very fine emery paper.
(2)
Carefully degrease the cut area with CLEANING AGENTS (Material No. 11-004) and a lint-free cloth.
(3)
Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) to the cut and make it smooth with a spatula.
(4)
Make sure that dust does not touch the cut. Let the adhesive dry for between 10 hours and 12 hours.
Subtask 52-11-18-340-052
C. Repair the Cuts With a Large Depth (more than one third of the thickness of the seal).
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1)
Push on the seal, open the cut. Lightly rub the cut with very fine emery paper.
(2)
Carefully degrease the cut area with CLEANING AGENTS (Material No. 11-004) and a lint-free cloth.
1EFF : ALL 1 52-11-18Page 808 1 1 Feb 01/98 1 1 1CES 1
(3)
Apply a thin layer of BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) to the surface of the cut.
(4)
Push the edges of the cut together as much as possible. Let it dry for some minutes.
(5)
Cut a piece of SPECIAL MATERIALS (Material No. 05-024) to cover the cut and apply a thin layer of BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) on the surface in contact with the repair area.
NOTE : If the cuts have a large depth, it is recommended to cut a
____ piece of SPECIAL MATERIALS (Material No. 05-024) of a sufficient dimension to put it on the perimeter of the seal.
(6)
Put the piece of SPECIAL MATERIALS (Material No. 05-024) over the cut and put a layer of foil SPECIAL MATERIALS (Material No. 05-023) on the repair area. Put the seal in the Wooden Bonding Block.
(7)
Compress the seal with the wooden block and a clamp. Let it dry for 24 hours.
(8)
Remove the wooden bonding block and the foil and remove the unwanted adhesive with fine emery paper.
5. Close-up
________ Subtask 52-11-18-420-051
A. Installation of the Door Seal.
(1) Install the door seal (Ref. TASK 52-11-18-400-001). Subtask 52-11-18-942-052
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Obey the special precautions after the work on the door (Ref. TASK 52-10-00-860-002).
(3) 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門1(164)
