(2)
 Make sure that the protrusion length J2 of the piston rod:

 (a)
 for the damper serie P/N FE174 and FE196 is 16.8 -1.8 +1.8 mm (0.6614 -0.0708 +0.0708 in.).

 (b)
 for the damper serie P/N FE240 is 21.8 -1.8 +1.8 mm (0.8582 -0.0708 +0.0708 in.).

 1EFF : ALL 1 52-11-14Page 407 1 1 Aug 01/99 1 1 1CES 1

 (3)
 If the protrusion length J2 is not in the tolerances, send the damper and emergency operation cylinder to the manufacturer for overhaul.

 (4)
 In this configuration, adjust the length J3 with the ADJUSTING TOOL -CYLINDER LENGTH (98D52103003000):

 (a)
 Remove the lockwire from the nut (20).

 (b)
 Loosen the nut (20).

 (c)
 Adjust the cylinder (19) to get the length J3.

 (d)
 Tighten the nut (20) and safety with MISCELLANEOUS (Material No. 19-010).

 1_ for the damper and emergency-operation cylinder serie P/N
 FE174 and FE196 358 mm (14.0944 in.).
 2_ for the damper and emergency-operation cylinder serie P/N
 FE240 363 +0.0 -2.0 mm (14.2913 +0.0000 -0.0787 in.).

 Subtask 52-11-14-420-057
 B. Installation of the Door-Damper and Emergency-Operation Cylinder (Ref. Fig. 401/TASK 52-11-14-991-007)
 (1)
 Put the yoke (6) in position and install the yoke pin (5) in the cylinder end fitting.

 (2)
 Install the two circlips (4) at the two ends of the yoke pin (5).

 (3)
 Put the cylinder end fitting on the support arm and hold it.

 (4)
 Install the bush (7).

 (5)
 Install the washer (8) and the bolt (9).

 (6)
 Install the washer (3) and the nut (2). Do not tighten the nut (2).

 (7)
 Install the bushes (23) and (24) on the fork (11).

 (8)
 Install the washer (13), the bushes (15), the end of the door damper (10), the washer (16), the fork (11), the bolt (12) and the nut (17).

 NOTE : If you install a new bolt (12), drill a hole of dia. 2 mm
____ (0.0787 in.) for the cotter pin installation.
 1EFF : ALL 1 52-11-14Page 408 1 1 Aug 01/99R 1 1 1CES 1

 (9) TORQUE the nut (2) to between 0.35 and 0.7 m.daN (30.97 and 61.94 lbf.in), and the nut (17) to between 1 and 1.7 m.daN (88.49 and 150.44 lbf.in).
 (10) Install the cotter pin (1), and the cotter pin (18). 
R  Subtask 52-11-14-740-051 
R  C. Not Applicable
 Subtask 52-11-14-220-056 
R RR  D. Check of the Door Opening/Closing (Ref. Fig. 401/TASK 52-11-14-991-007) 
R R R  (1) When you open/close the door, make sure that the clearance J4 between the telescopic rod (14) and the door attach fitting (23) is 1.5 mm (0.0590 in.) minimum.
 Subtask 52-11-14-210-062 
R  E. Check of the Pressure
 (1) Do a check of the pressure of the door-damper and emergency-operation cylinder (Ref. TASK 52-11-14-200-001).
 Subtask 52-11-14-820-055 
R  F. Adjustment of the Percussion Bellcrank Finger
 (1) Adjust the percussion bellcrank finger (Ref. TASK 52-11-14-820-002).
 5. Close-up________
 Subtask 52-11-14-410-069
 A. Installation of the Support Arm Lining
 (1) Install the door support arm lining panels (Ref. TASK 25-23-46-400-001).
 (a) For the left passenger/crew door: 831FZ, 831GZ.
 (b) For the right passenger/crew door: 841FZ, 841GZ.

 1EFF : ALL 1 52-11-14Page 409 1 1 Aug 01/99 1 1 1CES 1 1EFF : ALL 1 52-11-14Page 410 1 1 Aug 01/99 1 1 1CES 1

R  Subtask 52-11-14-861-055 
R  B. Not Applicable
 Subtask 52-11-14-865-068 
R  C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 13WN, 15WN, 48WV
 Subtask 52-11-14-410-070 
R  D. Close Access
 (1) Arm the percussion mechanism of the door damper and emergency operation cylinder. To do this, obey the special precautions after the work on the door (Ref. TASK 52-10-00-860-002).
 (2) Make sure that the work area is clean and clear of tool(s) and other items.
 (3) Close the passenger/crew door (Ref. TASK 52-10-00-410-001), 831, 841.
 (4) Remove the access platform(s).

 TASK 52-11-14-000-002 Removal of the Telescopic Rod
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門1(153)