B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
1EFF : ALL 1 52-11-18Page 405 1 1 May 01/05 1 1 1CES 1 C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-10-00-410-001 Closing of the Passenger/Crew Door 52-10-00-860-001 Special Precautions before Work on the Passenger/Crew Door 52-10-00-860-002 Special Precautions after Work on the Passenger/Crew Door 52-11-18-991-001 Fig. 401 R 52-11-18-991-006 Fig. 402
3. Job Set-up
__________
Subtask 52-11-18-010-056
A. Aircraft Maintenance Configuration
(1)
Make sure that the platform is in position.
(2)
Make sure that the applicable passenger/crew door are open 831, 841.
(3)
Make sure that the special precautions are obeyed (Ref. TASK 52-10-00-860-001).
Subtask 52-11-18-110-050
B. Cleaning.
(1) Clean the seal and the working surface and apply CLEANING AGENTS (Material No. 11-004).
4. Procedure
_________
Subtask 52-11-18-420-052
A. Installation of the Door Seal.
(Ref. Fig. 401/TASK 52-11-18-991-001)
(1)
Put the seal (22) on the passenger/crew door.
(2)
Install the retainer (19), the screws (18), (3), and the nuts (2) and tighten them with your hand.
1EFF : ALL 1 52-11-18Page 406 1 1 Nov 01/98 1 1 1CES 1
(3)
Install the retainer (20), the screws (18), and the nuts (2) and
tighten them with your hand.
(4)
Install the retainer (21), the screws (18), and the nuts (2) and
tighten them with your hand.
(5)
Install the retainer (1), the screws (3), (18), and the nuts (2) and tighten them with your hand.
(6)
Install the retainer (4), the screws (3), and the nuts (2) and
tighten them with your hand.
(7)
Install the retainer (17), the screws (3), and the nuts (2) and
tighten them with your hand.
(8)
Install the retainer (5), the screws (3), and the nuts (2) and
tighten them with your hand.
(9)
Install the retainer (6), the screws (3), and the nuts (2) and
tighten them with your hand.
(10)
Install the retainer (16), the screws (3), and the nuts (2) and tighten them with your hand.
(11)
Install the retainer (15), the screws (3), and the nuts (2) and tighten them with your hand.
(12)
Install the retainer (7), the screws (3), and the nuts (2) and tighten them with your hand.
(13)
Install the retainer (8), the screws (3), and the nuts (2) and tighten them with your hand.
(14)
Install the retainer (14), the screws (3), and the nuts (2) and tighten them with your hand.
(15)
Install the retainer (13), the screws (3), and the nuts (2) and tighten them with your hand.
(16)
Install the retainer (12), the screws (3), and the nuts (2) and tighten them with your hand.
(17)
Install the retainer (11), the screws (3), and the nuts (2) and tighten them with your hand.
(18)
Install the retainer (10), the screws (3), and the nuts (2) and tighten them with your hand.
1EFF : ALL 1 52-11-18Page 407 1 1 Nov 01/98R 1 1 1CES 1
(19) Install the retainer (9), the screws (3), and the nuts (2) and tighten them with your hand.
(20) Make sure that the clearances between the retainers are 2 +1 -1 mm (0.0787 +0.0393 -0.0393 in.)
(21) Tighten all the nuts (2) to between 0.17 and 0.20 m.daN (15.04 and 17.69 lbf.in).
Subtask 52-11-18-220-050
R R B. Check of the Clearance (Ref. Fig. 402/TASK 52-11-18-991-006)
R R (1) Check of the seal compression
R R (a) Close the door.
R R R R (b) Make sure that the door seal is correctly compressed on all its length and that the seal compression clearance J1 is 4.5 +2 -2 mm (0.1771 +0.0787 -0.0787 in.).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門1(162)
