曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 1. General_______
 The rudder attach fittings are installed at the front spar of the rudder.
 There are seven rudder attach fittings and three actuator attach fittings.
 2. Component Location__________________ 
R  (Ref. Fig. 001) 
R  3. Description___________ 
R  A. Attach Fittings Location 
R  (1) The rudder attach fittings attach the rudder to hinge arms at the 
R  rear spar of the vertical stabilizer. 
R  (2) They are attached in line with the ribs of the vertical stabilizer 
R  spar-box as follows: 
R  - the attach fitting No. 1 in line with rib No. 2, 
R  - the attach fitting No. 2 in line with rib No. 4, 
R  - the attach fitting No. 3 in line with rib No. 5, 
R  - the attach fitting No. 4 in line with rib No. 6, 
R  - the attach fitting No. 5 in line with rib No. 7, 
R  - the attach fitting No. 6 in line with rib No. 9, 
R  - the attach fitting No. 7 in line with rib No. 11. 
R  (3) The actuator attach fittings AC1, AC2 and AC3 attach the rudder to 
R  the actuator of the servo control units. They are installed between 
R  the rudder attach fitting No. 2 and the rudder attach fitting No. 5. 
R  (4) All the attach fittings are made of aluminum alloy. They are riveted 
R  to the front spar and to the side shells of the rudder. Hi-Loks are 
R  used for the installation. 
R  (5) The hinge bolts through the bearings connect the rudder to the hinge 
R  arms of the vertical stabilizer spar-box. 
R  (6) Only the attach fitting No. 6 holds the vertical load of the rudder. 
R  (7) The attach fitting No. 1 is installed together with a fork for the 
R  connection of the rudder position transmitter.

 

 Rudder Attach Fittings
 Figure 001
 1EFF :  ALL  1  55-46-00 Page 2 
1  1  Feb 01/98
 1  1
 1CES  1

 

 HINGE BEARING NO. 6 - RUDDER - REMOVAL/INSTALLATION
___________________________________________________
 TASK 55-46-11-000-001
 Removal of Rudder Hinge Bearing No. 6
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific warning notice
 No specific access platform 10.5 m (34 ft. 5 in.)
 98D55307528000 1 TOOL SET - R/I RUDDER BEARING NO. 6

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
 Configuration before Maintenance Action R 55-33-13-000-001 Removal of the Trailing Edge Access-Panels 325EL, R 325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BR
 55-36-41-000-001 Removal of the Hinge Arm Fittings No. 1 thru No. 7 55-36-48-000-001 Removal of the Rudder Support Strut 55-46-11-991-001 Fig. 401

 3. Job Set-up
__________
 Subtask 55-46-11-865-050
 A. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 15CE1 B11 49VU FLIGHT CONTROLS/THS/ACTR/MOT2 19CE2 B09 49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08 49VU AUTO FLT/FAC1/28VDC 5CC1 B04 49VU AUTO FLT/FAC1/26VAC 14CC1 B03 105VU FLIGHT CONTROLS/ELAC2/STBY SPLY 16CE2 A02 105VU FLT CTL/ELAC1/STBY SPLY 16CE1 A01 105VU FLT CTL/SEC1/STBY SPLY 22CE B01 121VU AUTO FLT/RUDDER/TRIM/IND 15CC M20 121VU AUTO FLT/FAC2/28VDC 5CC2 M19 121VU AUTO FLT/FAC2/26VAC 14CC2 M18 121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19 121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18 121VU FLIGHT CONTROLS/THS ACTR/MOT3 19CE3 Q17 121VU FLIGHT CONTROLS/THS ACTR/MOT1 19CE1 Q16 121VU FLIGHT CONTROLS/ELAC2/NORM/SPLY 15CE2 R20
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STABILIZERS 安定面(117)