3. Job Set-up
__________
Subtask 55-33-13-860-051
A. Aircraft Maintenance Configuration
(1)
Make sure that the rudder pedals are in the neutral position.
(2)
Make sure that the warning notice is in position to tell persons not to operate the flight controls.
(3)
Make sure that the access platform is in position.
(4)
Make sure that the Green, Blue and Yellow hydraulic systems are depressurized (Ref. TASK 29-00-00-864-001).
Subtask 55-33-13-865-057
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 15CE1 B11 49VU FLIGHT CONTROLS/THS/ACTR/MOT2 19CE2 B09 49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08 49VU AUTO FLT/FAC1/28VDC 5CC1 B04 49VU AUTO FLT/FAC1/26VAC 14CC1 B03 105VU FLIGHT CONTROLS/ELAC2/STBY SPLY 16CE2 A02 105VU FLT CTL/ELAC1/STBY SPLY 16CE1 A01 105VU FLT CTL/SEC1/STBY SPLY 22CE B01 121VU AUTO FLT/RUDDER/TRIM/IND 15CC M20 121VU AUTO FLT/FAC2/28VDC 5CC2 M19 121VU AUTO FLT/FAC2/26VAC 14CC2 M18 121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19 121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18 121VU FLIGHT CONTROLS/THS ACTR/MOT3 19CE3 Q17 121VU FLIGHT CONTROLS/THS ACTR/MOT1 19CE1 Q16 121VU FLIGHT CONTROLS/ELAC2/NORM/SPLY 15CE2 R20
1EFF : ALL 1 55-33-13Page 206 1 1 May 01/99R 1 1 1CES 1
4. Procedure
_________
(Ref. Fig. 201/TASK 55-33-13-991-002)
Subtask 55-33-13-420-051
A. Close/Install the access panels.
R R (1) Do a check for the condition of the sealant on the panel attach surfaces. If necessary, replace the sealant:
R R R R R R R R R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
R R (a) Apply the release agent SPECIAL MATERIALS (Material No. 05-013) to the rear surfaces of the trailing edge access panels.
R NOTE : Do not apply release agent to the bonding points.____
R R (b) Apply the SEALANTS (Material No. 09-018) to the panel attach surfaces of the rudder hinge arms and the spar-box flanges.
R NOTE : Do not apply sealant to the bonding points.____
R (2) Make sure that the work area is clean and clear of tool(s) and other items.
R (3) For access panels 325BL, 325BR, 325CL, 325CR and 325DL:
NOTE : The closing procedure for one access panel is given; the____ procedures for all access panels are almost the same.
(a) Remove the quick release pin (5).
(b) Slowly move the access panel to the closed position until you can install the quick release pin (5) in the pin stowage hole (4).
(c) Fully close the access panel.
(d) Tighten the studs (1).
R (4) For access panels 325EL, 325ER and 325DR:
NOTE : The installation procedure for one access panel is given; the____ procedures for all access panels are almost the same. 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM STABILIZERS 安定面(89)
