曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

_______ CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
 CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______ CARBONFIBER REINFORCED PLASTIC.
 NOTE : The removal procedures are given for the hinge arm fitting No. 1; the
____ removal procedures for the hinge arm fittings No. 2 thru No. 5 are almost the same.
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific warning notice No specific adjustable access platform 10.5 m (34 ft. 5 in.) SL90-314-5625 2 TOOL - EXTRACTION, TAB WASHERS STA-LOK NSA5454 SL90-314-7500 1 TOOL - EXTRACTION, TAB WASHERS STA-LOK NSA5454 SL90-322-5625 2 WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454 SL90-374-7500 1 WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454

 B. Referenced Information

 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
27-21-41-000-001 Removal of the Rudder 29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-002 Depressurize the Yellow Hydraulic System 29-10-00-864-003 Depressurize the Blue Hydraulic System 53-55-12-000-001 Removal of the Rudder Fairings 325AL and 325AR 55-33-13-000-001 Removal of the Trailing Edge Access-Panels 325EL,
 325ER, 325DL, 325DR, 325CL, 325CR, 325BL and 325BR
R 55-34-11-000-001 Removal of the Vertical Stabilizer Tip 55-36-48-000-001 Removal of the Rudder Support Strut 55-42-13-000-001 Removal of the Access Panel 326CT at the Rudder Attach Fitting No. 7 ASRM 51-42-11-001 55-36-41-991-001 Fig. 401 55-36-41-991-002 Fig. 402 55-36-41-991-003 Fig. 403
 3. Job Set-up
__________
 Subtask 55-36-41-865-050
 A. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 15CE1 B11 49VU FLIGHT CONTROLS/THS/ACTR/MOT2 19CE2 B09 49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08 49VU AUTO FLT/FAC1/28VDC 5CC1 B04 49VU AUTO FLT/FAC1/26VAC 14CC1 B03 105VU FLIGHT CONTROLS/ELAC2/STBY SPLY 16CE2 A02 105VU FLT CTL/ELAC1/STBY SPLY 16CE1 A01 105VU FLT CTL/SEC1/STBY SPLY 22CE B01 121VU AUTO FLT/RUDDER/TRIM/IND 15CC M20 121VU AUTO FLT/FAC2/28VDC 5CC2 M19 121VU AUTO FLT/FAC2/26VAC 14CC2 M18 121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19 121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18 121VU FLIGHT CONTROLS/THS ACTR/MOT3 19CE3 Q17 121VU FLIGHT CONTROLS/THS ACTR/MOT1 19CE1 Q16 121VU FLIGHT CONTROLS/ELAC2/NORM/SPLY 15CE2 R20

 Subtask 55-36-41-010-050

 B. Get Access
 (1) Get access to the hinge arm fittings No. 1 thru 5.
 (a)
 Put the warning notice in position to tell persons not to operate the flight controls.

 (b)
 Depressurize the Green, Yellow and Blue hydraulic systems (Ref. TASK 29-10-00-864-001) (Ref. TASK 29-10-00-864-002) (Ref. TASK 29-10-00-864-003).

 (c)
 Put the adjustable access platform in position.

 (d) Remove the access panels 325BL, 325CL, 325DL, 325BR, 325CR, 325DR R (Ref. TASK 55-33-13-000-001).
 (e) Remove the access panels 325AL, 325AR (Ref. TASK 53-55-12-000-001).
 NOTE : If you must remove more than one of the seven hinge arm
____ fittings, you must remove the rudder (Ref. TASK 27-21-41-000-001).
 Subtask 55-36-41-010-053
 C. Get Access
 (1)
 Get access to the hinge arm fitting No. 6.

 (a)
 Put the warning notice in position to tell persons not to operate the flight controls.

 (b)
 Depressurize the Green, Yellow and Blue hydraulic systems (Ref. TASK 29-10-00-864-001) (Ref. TASK 29-10-00-864-002) (Ref. TASK 29-10-00-864-003).

 

 (2)
 Put the adjustable access platform in position.

 (3)
 Remove the access panels 325DL, 325EL, 325DR, 325ER (Ref. TASK 55-33-13-000-001).

 

 (a) Remove the rudder support strut (16) (Ref. TASK 55-36-48-000-001).
 NOTE : If you must remove more than one of the hinge arm
____ fittings, you must remove the rudder (Ref. TASK 27-21-41-000-001).

R **ON A/C 001-049, 051-099, 101-105, 151-158, 201-210,
 Subtask 55-36-41-010-054
 D. Get Access
 (1) Get access to the hinge arm fitting No. 7.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STABILIZERS 安定面(97)