(2)
 Put a warning notice in position in the cockpit to tell persons not to operate the flight controls.

 (3)
 Put the rudder pedals in a neutral position.

 1EFF : ALL 1 55-34-11Page 402 1 1 Feb 01/00R 1 1 1CES 1

 4. Procedure
_________

 (Ref. Fig. 401/TASK 55-34-11-991-001)
 Subtask 55-34-11-020-054

 A. Removal of the Vertical Stabilizer Tip
 (1)
 Remove the static discharger (2) (Ref. TASK 23-61-41-000-001).

 (2)
 Remove the screws (3).

R (3) Attach the SLING - DORSAL FIN, LEADING EDGES, END CAP R (98D55307531001) to a crane.
 (4)
 Prepare the vertical stabilizer tip for hoisting.

 (a)
 Remove and discard the self-adhesive disc from the hoisting point.

 (b)
 Remove the plastic plugs from the hoisting point.

 (c)
 Install the hoist fitting (4) with the eye end out of the tip (1).

 (d)
 Attach the sling to the hoist fitting (4).

 (5)
 Operate the crane and slowly tighten the sling cable.

 (6)
 Lift the tip (1) clear of the vertical stabilizer and put it on a support.

 (7)
 Remove the sling.

 Vertical Stabilizer Tip 324AT
 Figure 401/TASK 55-34-11-991-001
 1EFF :  ALL  1  55-34-11 Page 404 
1  1  Feb 01/98
 1  1
 1CES  1

 TASK 55-34-11-400-001

R Installation of the Vertical Stabilizer Tip
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS
_______
 ONLY WITH A GOOD SUPPLY OF AIR.
 OBEY THE MANUFACTURERS INSTRUCTIONS.
 PUT ON PROTECTIVE CLOTHING.
 DO NOT GET THEM IN YOUR MOUTH.
 DO NOT SMOKE.
 DO NOT BREATHE THE GAS.
 THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT.
 GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.

 CAUTION : MAKE SURE YOU DO NOT DAMAGE THE ANTENNA.
_______
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific nonmetalic scraper
 No specific warning notices R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft)
 98D55307531001 1 SLING - DORSAL FIN, LEADING EDGES, END CAP

 B. Consumable Materials

 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
Material No. 05-013  D TV-53-3507/73 RELEASE AGENT (OBSOLETE USE 05-013A) (Ref. 20-31-00)
 Material No. 05-052 SELF-ADHES.PVC DISKS FOR HOISTING POINT BLANKING (Ref. 20-31-00)
R Material No. 09-016 USA MIL-PRF-81733D TYPE II CLASS B CORROSION INHIBITING FILLET CONSISTENCY (Ref. 20-31-00) Material No. 09-018 USA AMS 3267/3 CORROSION INHIBITING LOW ADHESION SEALANT (Ref. 20-31-00)
 C. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
20-28-00-869-002 Table of the Maximum Permitted Resistance Values 23-61-41-400-001 Installation of the Static Discharger 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
 Configuration before Maintenance Action
 55-34-11-991-001 Fig. 401

 3. Job Set-up
__________
 Subtask 55-34-11-860-050
 A. Aircraft Maintenance Configuration
 (1)
 Make sure that warning notices are in position in the cockpit to tell persons not to operate the flight controls.

 (2)
 Make sure that the Green, Blue and Yellow hydraulic system is depressurized (Ref. TASK 29-00-00-864-001).

 (3)
 Make sure that the rudder pedals are in the neutral position.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STABILIZERS 安定面(94)