Subtask 55-22-11-481-050
C. Install Locking Devices R (1) Put the PIN-SIDE STICK LOCKING (98D27903500000) in the CAPT and F/O side stick controllers. R (2) Install the COLLAR-ELEVATOR SERVOCONTROL SAFETY (98D27309005000) on
the servocontrol eleavators.
Subtask 55-22-11-941-050
D. Safety Precautions
(1)
Put the warning notices in the flight compartment to tell persons not to operate the flight controls.
(2)
Put the warning notices in position to tell persons not to operate the hydraulic systems.
(3)
Put the access platform in position at zone 330 for the left hand elevator and/or zone 340 for the right hand elevator.
Subtask 55-22-11-020-050
E. Access
(1) Remove the THS trailing edge access panels as necessary (Ref. TASK 55-13-11-000-001)
4. Procedure
_________
(Ref. Fig. 401/TASK 55-22-11-991-001)
Subtask 55-22-11-020-052
A. Remove Access Panels
(1)
Remove the screws (5).
(2)
Remove the leading-edge access panels (1), (2), (3) and (4).
INTENTIONALLY BLANK
R 1 1
55-22-11Page 404
1 1 Aug 01/99 1 1 1CES 1
Elevator Leading Edge-Removal/Installation
Figure 401/TASK 55-22-11-991-001
1EFF : ALL 1 55-22-11 Page 405
1 1 Feb 01/98
1 1
1CES 1
TASK 55-22-11-560-001
Preparation for the Installation
WARNING : DO NOT GET THE COMPOUND ON YOUR SKIN.
_______ IF YOU DO:
-RUB IT OFF IMMEDIATELY WITH A CLEAN CLOTH
-WASH THE SKIN WITH SOAP AND RINSE WITH CLEAN WATER. WARNING : IF YOU GET THE FLUID ON YOUR SKIN OR IN YOUR EYES:
_______
-FLUSH IT AWAY WITH CLEAN WATER
-GET MEDICAL AID. WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______ MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______ FALL CAN INJURE OR KILL YOU.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______ CARBONFIBER REINFORCED PLASTIC.
1. Reason for the Job__________________ Self Explanatory A. Aircraft Maintenance Configuration
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R R R No specific 98D27309001000 98D27903500000 nonmetallic scraper 1 TOOL-ELEVATOR NEUTRAL SETTING 2 PIN-SIDE STICK LOCKING
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-008 (USE 11-008A) (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-10-00-864-001 Depressurize the Green Hydraulic System
29-10-00-864-002 Depressurize the Yellow Hydraulic System
29-10-00-864-003 Depressurize the Blue Hydraulic System
55-13-11-000-001 Removal of the THS Trailing Edge Access Panels
3. Job Set-up__________
Subtask 55-22-11-860-051
(1) Make sure that the hydraulic systems are depressurized (Ref. TASK 29-10-00-864-001), (Ref. TASK 29-10-00-864-002), (Ref. TASK 29-10-00-864-003).
R (2) Make sure that the PIN-SIDE STICK LOCKING (98D27903500000) is in the CAPT and F/O side stick controllers.
R (3) Make sure that the TOOL-ELEVATOR NEUTRAL SETTING (98D27309001000) is R installed on the elevator.
(4)
Make sure that the warning notices are in the flight compartment to tell persons not to operate the flight controls.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STABILIZERS 安定面(62)
