(5)
Make sure that the warning notices are in position to tell persons not to operate the hydraulic systems.
(6)
Make sure that the access platforms are in position at zone 330 and/or zone 340.
(7)
Make sure that the THS trailing edge access panels have been removed as necessary (Ref. TASK 55-13-11-000-001).
4. Procedure
_________
Subtask 55-22-11-140-050
A. Cleaning
(1) Remove the old sealant from the mating surfaces of the leading edge access panels, the ribs and the skin panels. Use a nonmetallic scraper.
Subtask 55-22-11-110-050
B. Cleaning
(1) Clean the mating surfaces with CLEANING AGENTS (Material No. 11-008). Subtask 55-22-11-210-050
C. Visual Inspection
(1) Make sure that the anchor nuts are in a good condition.
TASK 55-22-11-400-001
Installation of the Elevator Leading Edge Access Panels 335AB (345AB), 335BB (345BB), 335CB (345CB), 335DB (345DB).
WARNING : DO NOT GET THE COMPOUND ON YOUR SKIN.
_______ IF YOU DO:
-RUB IT OFF IMMEDIATELY WITH A CLEAN CLOTH
-WASH THE SKIN WITH SOAP AND RINSE WITH CLEAN WATER. WARNING : IF YOU GET THE FLUID ON YOUR SKIN OR IN YOUR EYES:
_______
-FLUSH IT AWAY WITH CLEAN WATER
-GET MEDICAL AID. WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______ MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______ FALL CAN INJURE OR KILL YOU.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______ CARBONFIBER REINFORCED PLASTIC.
1. Reason for the Job__________________ Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R 98D27309005000 1 COLLAR-ELEVATOR SERVOCONTROL SAFETY R 98D27903500000 2 PIN-SIDE STICK LOCKING
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 05-013 D TV-53-3507/73 RELEASE AGENT (OBSOLETE USE 05-013A) (Ref. 20-31-00) Material No. 09-001 USA MIL-S-8802 TYPE I CLASS A FUEL TANK SEALANTPOLYSULFIDE (Ref. 20-31-00) Material No. 09-005 USA MIL-S-81733 CLASS C CORROSION INHIBITIVE INTERFAY SEALANT (Ref. 20-31-00) Material No. 11-008 (USE 11-008A) (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-002 Depressurize the Yellow Hydraulic System 29-10-00-864-003 Depressurize the Blue Hydraulic System 55-13-11-000-001 Removal of the THS Trailing Edge Access Panels 55-13-11-400-001 Installation of the THS Trailing Edge Access Panels 55-22-11-991-001 Fig. 401
3. Job Set-up
__________
Subtask 55-22-11-860-052
A. Aircraft Maintenance Configuration
(1) Make sure that the hydraulic systems are depressurized (Ref. TASK 29-10-00-864-001), (Ref. TASK 29-10-00-864-002), (Ref. TASK 29-10-00-864-003).
R (2) Make sure that the PIN-SIDE STICK LOCKING (98D27903500000) is in the CAPT and F/O side stick controllers.
R (3) Make sure that the COLLAR-ELEVATOR SERVOCONTROL SAFETY
R (98D27309005000) is installed on the servo control elevaotrs.
(4)
Make sure that the warning notices are in the flight compartment to tell persons not to operate the flight controls.
(5)
Make sure that the warning notices are in position to tell persons not to operate the hydraulic systems.
(6)
Make sure that the access platforms are in position at zone 330 and/or zone 340.
(7)
Make sure that the THS trailing edge access panels have been removed as necessary (Ref. TASK 55-13-11-000-001).
4. Procedure
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STABILIZERS 安定面(63)
