Vertical Stabilizer Attach Fittings
Figure 001
1EFF : ALL 1 55-36-00 Page 2
1 1 Feb 01/98
1 1
1CES 1
VERTICAL STABILIZER ATTACH FITTINGS - INSPECTION/CHECK
______________________________________________________
TASK 55-36-00-210-001
Detailed Visual Inspection of the Vertical Stabilizer Attach Fittings Including the Load Introduction Area at the Skin Panels
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______ MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS
_______ ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
1. Reason for the Job
__________________
Refer to the MPD TASK: 553004-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific lint-free cloth
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R Material No. 11-003 USA ASTM D 740 METHYL-ETHYL-KETONE (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
53-55-11-000-001 Removal of the Fairings 323AL/323AR
53-55-11-400-001 Installation of the Fairings 323AL/323AR
ASRM 55-31-00-101 (for corrective action)
55-36-00-991-001 Fig. 601
3. Job Set-up
__________
Subtask 55-36-00-010-050
A. Get Access
(1)
Remove the fairings 323AL and 323AR (Ref. TASK 53-55-11-000-001). WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE
_______
SPECIAL MATERIAL.
THIS MATERIAL IS DANGEROUS.
(2)
Carefully clean the inspection area with CLEANING AGENTS (Material No. 11-003) and a lint-free cloth.
4. Procedure
_________
(Ref. Fig. 601/TASK 55-36-00-991-001)
Subtask 55-36-00-210-050
A. Do a detailed visual inspection of the vertical stabilizer attach fittings including the load introduction area at the skin panels.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 55-31-00-101) for the
____
correct repair procedure.
Inspection Area Figure 601/TASK 55-36-00-991-001
1EFF : 1 1R 1CES ALL 1 11 1 55-36-00 Page 603 Nov 01/04
5. Close-up
________ Subtask 55-36-00-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the fairings 323AL and 323AR (Ref. TASK 53-55-11-400-001).
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 55-36-00Page 604 1 1 Nov 01/04R 1 1 1CES 1
ATTACH FITTINGS - HINGE ARM - REMOVAL/INSTALLATION
__________________________________________________
TASK 55-36-41-000-001
Removal of the Hinge Arm Fittings No. 1 thru No. 7
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STABILIZERS 安定面(96)
