(5)
 Make sure that the rudder support strut is removed (Ref. TASK 55-36-48-000-001).

 (6)
 Make sure that the hinge arm fitting No. 6 is removed (Ref. TASK 55-36-41-000-001).

 Subtask 55-46-11-865-051
 B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 15CE1 B11 49VU FLIGHT CONTROLS/THS/ACTR/MOT2 19CE2 B09 49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08 49VU AUTO FLT/FAC1/28VDC 5CC1 B04 49VU AUTO FLT/FAC1/26VAC 14CC1 B03
R 105VU FLIGHT CONTROLS/ELAC2/STBY SPLY 16CE2 A02 R 105VU FLT CTL/ELAC1/STBY SPLY 16CE1 A01 R 105VU FLT CTL/SEC1/STBY SPLY 22CE B01 R
 121VU AUTO FLT/RUDDER/TRIM/IND 15CC M20 121VU AUTO FLT/FAC2/28VDC 5CC2 M19 121VU AUTO FLT/FAC2/26VAC 14CC2 M18 121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19 121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18 121VU FLIGHT CONTROLS/THS ACTR/MOT3 19CE3 Q17 121VU FLIGHT CONTROLS/THS ACTR/MOT1 19CE1 Q16 121VU FLIGHT CONTROLS/ELAC2/NORM/SPLY 15CE2 R20
 4. Procedure
_________
 Subtask 55-46-11-420-050
 A. Install the rudder hinge bearing No. 6.
 (Ref. Fig. 401/TASK 55-46-11-991-001)

 (1)
 Remove the sealant from the rudder attach fitting with the nonmetallic scraper and CLEANING AGENTS (Material No. 11-003).

 (2)
 Clean the component interface and/or the adjacent area.

 (3)
 Do an inspection of the component interface and/or the adjacent area.

 (4)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 (5)
 Apply COMMON GREASE (Material No. 04-004) to the bearing (2). NOTE : Make sure that the outer surfaces stay clean.

____

 (6)
 Install the bearing (2) in the rudder attach fitting.

 (7)
 Install the retaining ring (3) and the ring nut (4). TORQUE the ring nut (4) to 6.0 m.daN (44.24 lbf.ft) with the TOOL SET - R/I RUDDER BEARING NO. 6.

 (8)
 Safety the ring nut (4) with the retaining ring (3). WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE

_______
 SPECIAL MATERIAL.
 THIS MATERIAL IS DANGEROUS.

 (9)
 Apply SEALANTS (Material No. 09-018) around the bearing (2) and the ring nut (4).

 (10) Install the hinge arm fitting (Ref. TASK 55-36-41-400-001).
 (11) Install the rudder support strut (Ref. TASK 55-36-48-400-001). Subtask 55-46-11-865-052
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 19CE1, 19CE2, 19CE3, 15CE1, 16CE1, 15CE2, 16CE2, 5CC1, 5CC2, 14CC1, 14CC2, 15CC, 22CE, 21CE1, 21CE2, 21CE3.
 Subtask 55-46-11-720-050
 C. Do an operational test of the rudder mechanical control (Ref. TASK 27-21-00-720-002).
 1EFF : ALL 1 55-46-11Page 408 1 1 Feb 01/99R 1 1 1CES 1

 5. Close-up
________
 Subtask 55-46-11-410-050

 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
R (2) Install the access panels 325EL, 325DL, 325ER, 325DR (Ref. TASK 55-R 33-13-400-001).
 (3)
 Remove the access platform(s).

 (4)
 Remove the warning notice(s).

 (5)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.