-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job__________________
Refer to the MPD TASK: 323300-01
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific safety barriers No specific warning notice No specific wedge 98A27003001000 1 RIGGING PIN 98A27801001000 1 RIGGING PIN 98A27901002000 1 PIN, RIGGING - RUDDER CONTROL 98A32301000000 3 RIGGING PIN 98DNSA20208040 1 RIGGING PIN 98DNSA20208060 9 RIGGING PIN
1EFF : ALL 1 32-33-00Page 621 1 1 Aug 01/05R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
20-24-12-200-001 Check of the Control Cables 25-54-12-000-001 Removal of the FWD Cargo Compartment Partition FR34 25-54-12-400-001 Installation of the FWD Cargo Compartment Partition
FR34 32-12-00-010-001 Open the Main Gear Doors for Access 32-12-00-410-001 Close the Main Gear Doors after Access 32-22-00-010-001 Nose Gear Doors - Ground Doors Opening 32-22-00-410-001 Nose Gear Doors - Ground Doors Closing 52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the
Yellow Electric Pump 52-30-00-860-002 Close the FWD or AFT Cargo-Compartment Door with the
Yellow Electric Pump 52-41-00-010-002 Open the Avionics Compartment Doors for Access 52-41-00-410-002 Close the Avionics Compartment Doors after Access 53-12-11-000-001 Removal of the Cockpit Floor Panels from FR1 Thru
FR12 53-12-11-400-001 Installation of the Cockpit Floor Panels from FR1
thru FR12 53-12-12-000-001 Removal of the Cabin Floor Panels from FR12 thru FR24 53-12-12-400-001 Installation of the Cabin Floor Panels from FR12 thru
FR24
53-22-12-000-001 Removal of the Cabin Floor Panels
53-22-12-400-001 Installation of the Cabin Floor Panels
53-32-12-000-002 Removal of the Cabin Floor Panels
53-32-12-400-002 Installation of the Cabin Floor Panels
32-33-00-991-019 Fig. 601
**ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,
32-33-00-991-020 Fig. 602
R **ON A/C 151-199, 401-499,
32-33-00-991-020-A Fig. 602A
**ON A/C ALL
32-33-00-991-021 Fig. 603
1EFF : ALL 1 32-33-00Page 622 1 1 Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
R 32-33-00-991-007 R **ON A/C 301-399,
R 32-33-00-991-007-A R **ON A/C ALL
R 32-33-00-991-008
3. Job Set-up
__________
Fig. 608
Fig. 608A
Fig. 609
(Ref. Fig. 601/TASK 32-33-00-991-019)
**ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,
(Ref. Fig. 602/TASK 32-33-00-991-020) R **ON A/C 151-199, 401-499,
(Ref. Fig. 602A/TASK 32-33-00-991-020-A)
**ON A/C ALL
(Ref. Fig. 603/TASK 32-33-00-991-021)
Subtask 32-33-00-941-064
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Make sure that the ground safety locks are on the landing gear.
1EFF : ALL 1 32-33-00Page 623 1 1 Aug 01/05 1 1 1CES 1
(3)
On the panel 400VU:
-make sure that the landing-gear control-lever 6GA is in the DOWN position
-put a warning notice in position to tell persons not to operate the landing gear.
(4)
On the panel 110VU, make sure that the GRAVITY GEAR EXTN handle is folded into the center console.
(5)
Install a wedge on each side of the GRAVITY GEAR EXTN handle to lock the handle in position.
**ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,
Subtask 32-33-00-010-051
B. Get Access
(1)
Open the NLG doors (Ref. TASK 32-22-00-010-001).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架5(128)
