(e)
Make sure that the electrical connectors are clean and in the correct condition.
(f)
Connect the electrical connectors (5) and (6) to the uplock assembly (8).
(7)
Connect the Bonding Strap view E
(a) Put the bonding strap (13) in position and install the bolt (14), the washer (22) and the nut (21) (Ref. TASK 20-28-00-912-004).
(8)
Install the SETTING TOOL-UPLOCK (98D32104018000) view H and J
(a)
Connect a hydraulic cart and slowly retract the landing gear until the gear pin is engaged and lock in the uplock assembly.
(b)
Measure the dimension "W" at the setting tool. NOTE : The initial setting at the setting tool is between 177 mm
____ (6.97 in.) minimum and 201 mm (7.91 in.) maximun.
(c) If the dimension "W" is not between the values 168 mm (6.61 in.) minimum and 186 mm (7.32 in.) maximum, adjust as follows (second adjustment):
1_ Slowly lower the landing gear
2_ Remove the nut (2), the bolt (11), the washer (12), and the
outer bush (1) from the attachment bracket and eye end of the
uplock assembly.
3_ Cut and remove the lock wire from the eye end-lock nut if
installed.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-31-44Page 443 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
4_ Loosen the eye end-lock nut.
5_ Turn the eye end IN or OUT to get the dimension "X" = 97 +1 -1
mm (3.82 in. +0.04 -0.04 in.).
6_ Tighten the lock nut with the hand.
(9) Make sure that the strut A (4) is has a length of 163.6 +0.5 -0.5 mm
(6.44 +0.02 -0.02 in.).
(10) Make sure that the strut B (10) has a length of 226.7 +0.5 -0.5 mm
(8.93 +0.02 -0.02 in.).
NOTE : After the adjustment of the eye end, make sure that the
____ distance between the eye end centres is not more than the following:
-
For strut "A" = 177 mm (6.97 in.) maximum and 160 mm (6.30 in.) minimum (dimension "Y"),
-
For strut "B" = 239 mm (9.41 in.) maximum and 222 mm (8.74 in.) minimum (dimension "Z").
(11)
Put eye end in position in the attachment bracket view B.
(12)
Install the bolt (11), the washer (12), the outer bush (1) and the nut (2).
(13)
Do step 4. A. (8) (a) and (b) again and ensure that dimension "W" is correct.
(14)
If dimension "W" is not correct, do step 4. A. (8) (c) -1 through -6 until dimesion "W" is correct.
NOTE : Dimension "W" will change when the eye end is rotated. A half
____ turn of the eye end will change the length with 1 mm (0.04 in.).
(15)
Tighten the eye end-lock nut and TORQUE to 14.6 m.daN (107.66 lbf.ft).
(16)
Safety the eye end with MISCELLANEOUS (Material No. 19-010).
(17)
TORQUE the nut (2) to between 6.8 and 7.8 m.daN (50.14 and 57.52 lbf.ft) .
(a)
Safety the nut (2) with a new cotter pin (3).
(b)
Safety the nut (16) with a new cotter pin (15).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-31-44Page 444 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(c) Safety the nut (27) with a new cotter pin (28).
(18) Connect the Free Fall Lever (29) view D
(a)
Apply SPECIAL MATERIALS (Material No. 05-002) to the splined shaft of the new uplock assembly (8), the bolt (39) and the washer (30).
(b)
Put the lever (29) in position on the splined shaft of the uplock assembly (8). Make sure that the master splines are aligned.
(c)
Install the bolt (39), the washer (30) and the nut (31).
(d)
Safety the nut (31) with a new cotter pin (32).
(e)
Install the Free Fall Rod (35) VIEW D. (Ref. Fig. 401/TASK 32-31-44-991-001)
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE
_______ SPECIAL MATERIAL. THIS MATERIAL IS DANGEROUS.
(f)
Install the RIGGING PIN (98DNSA20208060) at rigging points 1 and
2.
(g)
If necessary, adjust the adjustable rod (35)
(h)
Apply SPECIAL MATERIALS (Material No. 05-002) to the bolt (33), the bush (34) and the washer (37).
(i)
Put the rod (35) in position and install the bush (34), the bolt (33), the washer (37) and the nut (36).
(j)
Safety the nut (36) with a new cotter pin (38).
