(2)
Turn the GRAVITY GEAR EXTN handle counterclockwise three full turns.
(3)
Fold the GRAVITY GEAR EXTN handle into the center console.
(4)
Install a wedge on each side of the GRAVITY GEAR EXTN handle to lock the handle into position.
Subtask 32-33-00-210-060
C. Detailed Inspection of the Free-Fall Mechanism Cables after the Free-fall Mechanism has been Moved
(1)
Check the part of the cables that could not be seen before (from FR7 thru FR12) (Ref. TASK 20-24-12-200-001) to make sure that:
-they do not have kinks, broken wires or too much wear.
(2)
Check the part of the cables that could not be seen before (from FR12 thru FR16) (Ref. TASK 20-24-12-200-001) to make sure that:
-they do not have kinks, broken wires or too much wear.
(3)
Check the part of the cables that could not be seen before (from FR14 thru FR24A - Passenger Compartment) (Ref. TASK 20-24-12-200-001) to make sure that:
-they do not have kinks, broken wires or too much wear.
1EFF : ALL 1 32-33-00Page 637 1 1 Aug 01/05R 1 1 1CES 1
(4)
Check the part of the cables that could not be seen before (from FR24A thru FR36 - Forward Compartment) (Ref. TASK 20-24-12-200-001) to make sure that:
-they do not have kinks, broken wires or too much wear.
(5)
Check the part of the cables that could not be seen before (from FR34 thru FR46 - MLG Bay) (Ref. TASK 20-24-12-200-001) to make sure that:
-they have no kinks, broken wires or signs of wear. Subtask 32-33-00-860-078
D. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE WARNING NOTICES ARE IN POSITION WHEN YOU
_______ MOVE THE FREE-FALL MECHANISM CABLES. INJURY CAN OCCUR IF PERSONNEL OR LOOSE CLOTHING BECOME CAUGHT IN THE MECHANISM.
WARNING : MAKE SURE THERE ARE NO PERSONNEL NEAR THE FREE-FALL MECHANISM
_______ CABLES BEFORE YOU TURN THE GRAVITY GEAR EXTN HANDLE. INJURY CAN OCCUR IF PERSONNEL OR LOOSE CLOTHING BECOME CAUGHT IN THE FREE-FALL MECHANISM.
(1)
On the panel 110VU, remove the wedges from the GRAVITY GEAR EXTN handle. Move the GRAVITY GEAR EXTN handle from the folded position.
(2)
Turn the GRAVITY GEAR EXTN handle clockwise three full turns.
(3)
Fold the GRAVITY GEAR EXTN handle into the center console.
(4)
Install a wedge on each side of the GRAVITY GEAR EXTN handle to lock the handle into position.
Subtask 32-33-00-480-052
E. Installation of the Rigging Pins NOTE : It is important to install the rigging pins exactly as given in
____ the procedure. This will make sure that all the datum positions are correct.
(1) Install the RIGGING PIN (98A27801001000) at position Pin 1. Make sure that the rigging pin goes through the pulley frame and the pulley. Keep the rigging pin in position.
1EFF : ALL 1 32-33-00Page 638 1 1 Aug 01/05R 1 1 1CES 1
Subtask 32-33-00-210-056
F. Detailed Inspection from FR7 thru FR12:
(1)
Examine the GEAR GRAVITY EXTN handle for damage.
(2)
At the reduction gearbox make sure that:
-it is attached correctly and the parts that attach the gearbox are tight
-
the driveshaft is free from damage, cracks and distortion
-
the driveshaft is attached correctly
-
the pulley stop screws are safetied and tight
-
the pulley shear pins are not damaged or loose
-
the pulley is not loose, damaged or cracked.
(3)
Make sure that the transmission rod between the reduction gearbox and the pulley at FR8 is not loose, damaged or cracked.
(4)
Make sure that the two pulleys at FR8 and FR12 are not loose, damaged or cracked.
(5)
Make sure that the cable retaining pins on the pulley at FR12 are not damaged or cracked and are attached correctly.
Subtask 32-33-00-210-057
G. Detailed Inspection from FR12 thru FR16:
(1) At the pulley (FR16) make sure that:
-it is not loose, damaged or cracked
-
the support bracket is attached correctly
-
the vertical shaft is not loose, damaged or cracked.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架5(131)
