C. Get Access
(1)
Put the access platform in position below the applicable zone 123.
(2)
Open the NLG doors (Ref. TASK 32-22-00-010-001).
(3)
Make sure that a SAFETY PIN - NLG DOOR (98D32203502000) is installed in each NLG door (Ref. TASK 32-00-00-481-002).
Subtask 32-31-73-869-058
D. Flight Configuration Precautions
(1)
If the electrical power is not necessary for other maintenance tasks, de-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002). Then, it is not necessary to operate the LGCIU circuit breakers.
(2)
If the electrical power is necessary, do the precautions for flight configuration (Ref. TASK 32-00-00-860-001) before you open the LGCIU circuit breakers.
Subtask 32-31-73-865-067
E. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34
4. Procedure
_________ Subtask 32-31-73-210-084
A. Preparation for Inspection
(1) Do a check of the NLG extension/steering proximity sensors 24GA(25GA):
-check the target lever and attached link for wear or distortion (Ref. CMM 32-27-10).
1EFF : ALL 1 32-31-73Page 619 1 1 May 01/04R 1 1 1CES 1
Subtask 32-31-73-220-078-A
B. Inspection of the NLG Proximity Sensor and Target Clearances
(Ref. Fig. 605/TASK 32-31-73-991-015)
(1)
Measure and record the dimensions X and Z for the NLG downlock proximity sensors 18GA(19GA):
-
dimension X must be 6.5 mm (0.2559 in.) +/- 0.10 mm (0.0039 in.)
-
dimension Z must be 1.5 mm (0.0590 in.) +/- 0.10 mm (0.0039 in.).
(a) If the dimensions are incorrect, do the adjustment of the NLG downlock proximity sensors 18GA(19GA) (Ref. TASK 32-31-73-820-005).
(2)
Measure and record the dimensions X and Z for the NLG
extension/steering proximity sensors 24GA(25GA):
-
dimension X must be 1.35 mm (0.0531 in.) +/- 0.75 mm (0.0295 in.)
-
dimension Z must be 2.0 mm (0.0787 in.) +/- 0.20 mm (0.0078 in.).
(a) If the dimensions are incorrect, do the adjustment of the NLG extension/steering proximity sensors 24GA(25GA) (Ref. TASK 32-31-73-820-006).
(3)
Measure and record the dimensions X and Z for the NLG door open proximity sensors 36GA(37GA) and 38GA(39GA):
-
dimension X must be 2.5 mm (0.0984 in.) +/- 0.50 mm (0.0196 in.)
-
dimension Z must be 2.0 mm (0.0787 in.) +/- 0.50 mm (0.0196 in.).
(a) If the dimensions are incorrect, do the adjustment of the NLG door open proximity sensors 36GA(37GA), 38GA(39GA) (Ref. TASK 32-31-73-820-004).
Subtask 32-31-73-586-053
C. Aircraft Maintenance Configuration
(1) If you did a check of the proximity sensors 25GA and 24GA, lower the aircraft off jacks (Ref. TASK 07-11-00-586-001).
Subtask 32-31-73-865-068
D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1GA, 2GA, 52GA.
1EFF : ALL 1 32-31-73Page 620 1 1 May 01/04R 1 1 1CES 1
Subtask 32-31-73-869-059
E. Flight Configuration Precautions
(1) If you did the flight configuration precautions, put the aircraft back to the ground configuration (Ref. TASK 32-00-00-860-002).
Subtask 32-31-73-410-055
F. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the SAFETY PIN - NLG DOOR from each of the NLG doors.
(3)
Close the NLG doors (Ref. TASK 32-22-00-410-001).
中國航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護(hù)手冊 AMM LANDING GEAR 起落架5(92)
