曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  REMOVE/INSTALL THE WINDSHIELD. DO NOT USE A LEVER AGAINST THE 
R  EDGE OF THE WINDSHIELD BECAUSE IF YOU DO, YOU WILL CAUSE DAMAGE 
R  TO THE WINDSHIELD. 
R  (1) Install the adjustment tools (50) and (54) on the upper part of the 
R  windshield with the pins (52). Operate the suction cups of the 
R  adjustment tools (50) and (54). 
R  NOTE : Two persons are necessary to remove the windshield from its____ 
R  frame. 
R  (2) Adjust the knurled screws (51) to loosen the windshield panel from 
R  the lower side. 
R  (3) With the adjustment tool (54) in position, use the knurled nut (53) 
R  to move the windshield panel (14) against the center post. 
R  (4) Remove the R/I FRONT WINDOW TOOL (98F56103000000). 
R  (5) Install the vacuum handles (55) on the outer side of the windshield 
R  panel. 
R  (6) From the cockpit, push the windshield panel (14) with one hand on the 
R  upper section near the center post. 
R  A second person, out of the aircraft, gets the windshield panel (14) 
R  when it moves out of its frame at the center post.

 1EFF : ALL 1 56-11-11Page 434 1 1 Aug 01/05 1 1 1CES 1

R R  Windshield Panel - Removal/Installation Figure 408/TASK 56-11-11-991-023
 1EFF : 1 1 1CES  ALL  1 111 56-11-11 Page 435 Aug 01/05

 

R NOTE : If you must install the same windshield panel, put it into its
____ R container at the removal area.
R (7) Remove the windshield panel (14).
 1EFF : ALL 1 56-11-11Page 436 1 1 Aug 01/05 1 1 1CES 1

R TASK 56-11-11-400-001- 01

R  Installation of the Windshield 
R  WARNING : MAKE SURE THAT THE CIRCUIT BREAKERS RELATED TO THE WEATHER RADAR ARE_______ 
R  OPENED, SAFETIED AND TAGGED. 
R  1. Reason for the Job__________________ 
R  NOTE : For the windshield removal/installation, there are three tool____ 
R  alternatives: 
R  - 98D56103001000 
R  - 98F56103000000 
R  - SGSIT01. 
R  The tool 98F56103000000 is the newest tool developed by Airbus to 
R  make the windshield adjustment easier. 
R  This procedure is applicable to the tool 98F56103000000. 
R  For SGS tool SGSIT01, the procedure is included in SGS documentation. 
R  2. Job Set-up Information______________________ 
R  A. Fixtures, Tools, Test and Support Equipment 
R  -------------------------------------------------------------------------------
R  REFERENCE  QTY DESIGNATION 
R  -------------------------------------------------------------------------------
R  No specific  brush 
R  No specific  non metallic lever 
R  No specific  two wooden shims 1.4 mm (0.0551 in.) 
R  No specific  two wooden shims 7 mm (0.2755 in.) 
R  No specific  Torque Wrench : range 0.20 to 3.60 m.daN 
R  (2.00 to 26.00 lbf.ft) 
R  98F56103000000  2 R/I FRONT WINDOW TOOL

 1EFF : ALL 1 56-11-11Page 437 1 1 Aug 01/05 1 1 1CES 1R B. Consumable Materials

R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R  Material No. 04-012 
R 
R  Material No. 05-002 
R 
R  Material No. 08-052 
R 
R  Material No. 09-016 
R 
R 
R  Material No. 09-019 
R 
R 
R  Material No. 09-053 
R 
R  Material No. 11-003 
R 

USA VV-P-236
PURE MINERALVASELINE OR PETRO- LATUM (Ref. 20-31-00)
USA MIL-P-8116
PUTTY, ZINC CHROMATE GENERAL PURPOSE (Ref. 20-31-00)
USA MIL-T-23397 AND/OR L-T-80B
SELF ADHESIVEALUMINIUM TAPE (Ref. 20-31-00)
USA MIL-PRF-81733D TYPE II CLASS B
CORROSION INHIBITING FILLET CONSISTENCY
(Ref. 20-31-00)
USA AMS 3267/3
LOW ADHESION CORROSION INHIBITING SEALANT
(Ref. 20-31-00)

FAST-CURING SEALANT FOR WINDSCREENS (Ref. 20-31-00)
USA ASTM D 740
METHYL-ETHYL-KETONE (Ref. 20-31-00)

R C. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINDOWS 風擋 窗戶(24)