1EFF : 051-099, 1 56-12-11Page 469 1 1 May 01/05 1 1 1CES 1

R Subtask 56-12-11-420-059

R  B. Installation of the Sliding Window Panel 
R  (Ref. Fig. 415/TASK 56-12-11-991-029) 
R  CAUTION : BE CAREFUL DURING THE REMOVAL/INSTALLATION OF EACH SLIDING_______ 
R  WINDOW PANEL TO PREVENT INJURY TO PERSONS AND /OR DAMAGE. 
R  MAKE SURE THAT THERE ARE SUFFICIENT PERSONS DURING THE 
R  OPERATION. EACH WINDOW PANEL WEIGHS APPROXIMATELY 20Kg 
R  (44.11b). 
R  (1) Use 2 suction cups to move and hold the sliding window panel (30) in 
R  position during installation in its frame. 
R  (2) Put the sliding window panel (30) and the retainer (31) in position 
R  in its housing. 
R  (3) Move the frame of the sliding window to the closed position. 
R  (4) Install four screws (32) at the four corners of the frame . 
R  (5) Move the frame of the sliding window to the open position. 
R  (6) Install all the screws (32) and washers (33) and tighten with your 
R  hand. 
R  (7) Install 4 non metallic shims between the sliding window panel (30) 
R  and the retainer (31) to get a clearance A of 1.4 +1 -1 mm (0.0551 
R  +0.0393 -0.0393 in.). 
R  (8) Install the washers (33) and the screws (32) at the four corners of 
R  the frame. 
R  (9) Initially TORQUE the screws (32) to 0.2 m.daN (17.69 lbf.in). For the 
R  screw (32) behind the axis of the control handle, use the WRENCH, 
R  REMOVAL - SLIDING WINDOW (98D56103002001). 
R  (10) TORQUE the screws (32) to between 0.35 and 0.45 m.daN (30.97 and 
R  39.82 lbf.in). 
R  NOTE : TORQUE the screws (32) in a staggered pattern.____ 
R  (11) Remove the non metallic shims. 
R  (12) Apply SEALANTS (Material No. 09-016) in the peripheral gap.

 1EFF : 051-099, 1 56-12-11Page 470 1 1 May 01/05 1 1 1CES 1 1EFF : 051-099, 1 56-12-11Page 471 1 1 May 01/05 1 1 1CES 1

R  (13) Clean the remaining sealing compound between the window panel (30) 
R  and the retainer (31) with a MISCELLANEOUS (Material No. 19-003) 
R  soaked with CLEANING AGENTS (Material No. 11-003). 
R  **ON A/C 051-051, 
R  Subtask 56-12-11-220-059 
R  C. Check of the Clearance 
R  (Ref. Fig. 416/TASK 56-12-11-991-047) 
R  (1) Make sure that the sliding window is open. 
R  (2) Do a check of the out-of-flush clearance C between the retainer (34) 
R  and the sliding window panel (30). 
R  NOTE : The clearance C (edge-clearance) between the window frame and____ 
R  window panel, shows a defect in the flat surfaces of the panel 
R  and the frame. 
R  The edge-clearance location is at the window panel/frame edge. 
R  (a) Make sure that the out-of-flush clearance C between the retainer 
R  (34) and the glass sliding window (30) is 0.6 +0.8 -0.7 mm 
R  (0.0236 +0.0314 -0.0275 in.). 
R  (3) Close the sliding window. Make sure that the window moves easily. 
R  (4) From points 1 to 11 make sure that the out-of-flush B is 0 +0.6 -2 mm 
R  (0.0000 +0.0236 -0.0787 in.) on the periphery of the window panel. 
R  (5) If the out-of-flush B is not correct, adjust as follows: 
R  (a) Remove the circlips (42), (45), (46) and (51). 
R  (b) Loosen the nuts (41), (44), (47) and (50). 
R  (c) Turn the eccentrics (40), (43), (48) and (49) to get the correct 
R  out-of-flush B. 
R  (d) TORQUE the nuts (41), (44), (47) and (50) to between 0.6 and 0.7 
R  m.daN (53.09 and 61.94 lbf.in). 
R  (e) Safety the nuts (41), (44), (47) and (50) with BONDING AND 
R  ADHESIVE COMPOUNDS (Material No. 08-002A). 
R  (f) Install the circlips (42), (45), (46) and (51).

R Sliding Windows - Clearances
R Figure 416/TASK 56-12-11-991-047- 12 (SHEET 1)

 1EFF : 051-052, 1 56-12-11Page 472 1 1 May 01/05 1 1 1CES 1

R Sliding Windows - Clearances
R Figure 416/TASK 56-12-11-991-047- 22 (SHEET 2)

 1EFF : 051-052, 1 56-12-11Page 473 1 1 May 01/05 1 1 1CES 1 1EFF : 052-052, 1 56-12-11Page 474 1 1 May 01/05 1 1 1CES 1 1EFF : 052-099, 1 56-12-11Page 475 1 1 May 01/05 1 1 1CES 1
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINDOWS 風擋 窗戶(65)