R (5) Clean the external surfaces of the structure with CLEANING AGENTS
R (Material No. 11-003) to remove the remaining sealant from the
R structure.
R Subtask 56-11-11-420-060
R H. Installation of the Protection Plate
R (Ref. Fig. 402/TASK 56-11-11-991-002)
R (1) Install the spray nozzles (Ref. TASK 30-45-44-400-001).
R (2) Put the protection plate (19) in position.
R (3) Apply SPECIAL MATERIALS (Material No. 05-002) below the head of the
R screws (20), (21) and (22).
R (4) Install the screws (20), (21) and (23) and tighten them.
R Subtask 56-11-11-420-061
R J. Installation of the Components
R (Ref. Fig. 401/TASK 56-11-11-991-001)
R (1) Put the vertical lining panel in position on the windshield post (1).
R (2) Install the screws (2) and the washers (6).
R (3) Put the lining panel (4) in position.
R (4) Install the four stud assy (3) and tighten them.
R (5) Tighten the fastener (5) and the screws (2).
R Subtask 56-11-11-110-057
R K. Cleaning of the windshield
R (1) Remove the protective film from the windshield.
R (2) Clean the windshield (Ref. TASK 56-10-00-110-001).
R Subtask 56-11-11-865-065
R L. Remove the safety clip(s) and the tag(s) and close this(these) circuit
R breaker(s):
R 1LF, 1DG1, 4DG1, 5DG1, 1DG2, 4DG2, 5DG2, 5SQ1, 5SQ2.
R Subtask 56-11-11-710-051
R M. Test
R (1) Do the test of the anti-icing and defogging system of the windshield
R (Ref. TASK 30-42-00-710-001).
R 5. Close-up________
R Subtask 56-11-11-410-056
R A. Close Access
R (1) Install the wiper arm (Ref. TASK 30-45-52-400-002).
R (2) Remove the ground support and maintenance equipment, the special and
R standard tools and all other items.
R (3) Remove the access platform(s).
R (4) Remove the warning notice(s).
R (5) Make sure that the work area is clean and clear of tool(s) and other
R items.
1EFF : ALL 1 56-11-11Page 449 1 1 Aug 01/05 1 1 1CES 1 WINDSHIELD (3DG1,3DG2) - INSPECTION/CHECK
_________________________________________
TASK 56-11-11-200-001
Inspection of the Windshields
WARNING : MAKE SURE THAT THE CIRCUIT BREAKERS RELATED TO THE WEATHER RADAR ARE
_______
OPENED, SAFETIED AND TAGGED.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific access platform 4.50 m (14 ft. 9 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
56-10-00-110-001 Cleaning of the L/R Windshields R 56-10-00-200-004 Measurement of Scratch Depth with MITUTOYO Surface R Tester SJ201
56-11-11-300-002 Repair of the Soft Liner (SPS Windshield)
56-11-11-991-005 Fig. 601
56-11-11-991-006 Fig. 602
56-11-11-991-007 Fig. 603
56-11-11-991-008 Fig. 604
56-11-11-991-009 Fig. 605
56-11-11-991-010 Fig. 606
56-11-11-991-017 Fig. 607
56-11-11-991-019 Fig. 608
