(2) Examine the leading edge surfaces to make sure that:
-
there are no loose rivets
-
there is no damage
-
there is no corrosion.
Wing Leading Edge
Figure 601/TASK 57-41-00-991-001
1EFF : ALL 1 57-41-00 Page 604
1 1 Feb 01/98
1 1
1CES 1
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) fort he
____
correct repair procedure.
(3) Examine the access panels to make sure that:
-
there are no loose fasteners
-
there is no damage.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) fort he
____
correct repair procedure.
(4) Examine the outboard part of the leading edge and the inboard part of the wing tip to make sure that:
-
there is no distortion
-
there are no loose rivets
-
there is no damage
-
there is no corrosion.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) fort he
____
correct repair procedure.
(5) Examine the area above the nacelles to make sure that:
-
there are no loose rivets
-
there is no corrosion
-
there is no distortion.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) fort he
____
correct repair procedure.
(6) Examine the leading edge surfaces behind the slats to make sure that:
-
there is no distortion
-
there is no damage
-
there are no loose rivets
-
there is no corrosion.
-the condition of the abrasion-resistant finish on the top surface is good (Ref. Fig. 601, dimension 'X')
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) fort he
____
correct repair procedure.
5. Close-up
________
Subtask 57-41-00-865-051
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 7CV.
Subtask 57-41-00-860-059
B. Aircraft Configuration
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the access platform(s).
(3) Retract the slats (Ref. TASK 27-80-00-866-005). Subtask 57-41-00-942-050
C. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Remove the safety barriers.
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 57-41-00-200-002
Detailed Visual Inspection of Slat 1, Tracks 1-4: Visible Part of Roller Contact Area
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 574201-01
NOTE : Although this TASK is for slat-tracks 1 thru 4 only, the procedure is
____
the same for all slat-tracks.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notices No specific adjustable access platform 3.0 m (9 ft. 10 in.) 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00) C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(109)
