(2)
 Remove the warning notice(s).

 1EFF : ALL 1 57-26-00Page 681 1 1 Nov 01/04R 1 1 1CES 1

 TASK 57-26-00-200-008

 Detailed Visual Inspection of Outer Wing Rear Spar Aft Face Sidestay Fitting
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 572650-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notices No specific access platform 2.5 m (8 ft. 2 in.)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004  USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
 Material No. 19-003  USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 1EFF : ALL 1 57-26-00Page 682 1 1 Nov 01/04R 1 1 1CES 1

 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-00-00-481-001 Installation of the Safety Devices on the Landing
 Gears 32-12-00-010-001 Open the Main Gear Doors for Access 32-12-00-410-001 Close the Main Gear Doors after Access ASRM 572600 (for corrective action) 57-26-00-991-013 Fig. 613
 3. Job Set-up
__________ Subtask 57-26-00-941-062
 A. Safety Precautions
 (1)
 Put the safety barriers in position.

 (2)
 Put warning notices in the cockpit to tell persons not to operate the landing gears or the landing gear doors.

 (3)
 Make sure that the GROUND LOCK SLEEVE (460005833) or the GROUNDLOCK SLEEVE (460007280) is installed on each the MLG lockstay actuator (Ref. TASK 32-00-00-481-001).

 Subtask 57-26-00-010-065
 B. Get Access
 (1)
 Open the main landing gear doors (Ref. TASK 32-12-00-010-001).

 (2)
 Put the access platform in position below the sidestay-actuator attachment-bracket, zone 571(671).

 4. Procedure
_________ (Ref. Fig. 613/TASK 57-26-00-991-013) CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
 EDGE:

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1EFF : ALL 1 57-26-00Page 683 1 1 Nov 01/04R 1 1 1CES 1

 Outer Wing - Sidestay Attachment Bracket - Location Figure 613/TASK 57-26-00-991-013
 1EFF : 1 1R 1CES  ALL  1 11 1 57-26-00 Page 684 Nov 01/04

 Subtask 57-26-00-110-061
 A. Preparation for Inspection
 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL

_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-004) to clean the inspection area.
 Subtask 57-26-00-210-059
 B. Inspection
 (1) Examine the sidestay attachment bracket. Make sure that:
 -
there is no damage

 -
there is no corrosion

 -
there are no cracks

 -the surface protection is in the correct condition.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(36)