(3)
 Make sure that the warning notices are in position in the cockpit to tell persons not to operate the landing gear. bay, zone 571 (671).

 Subtask 57-26-13-860-053
 B. Aircraft Maintenance Configuration
 (1)
 Make sure that the access platform is in position below the applicable main landing gear.

 (2)
 Make sure that the applicable MLG actuating cylinder has been removed (Ref. TASK 32-31-46-000-001).

 1EFF : ALL 1 57-26-13Page 420 1 1 May 01/05R 1 1 1CES 1

 4. Procedure
_________

 (Ref. Fig. 402/TASK 57-26-13-991-002)
 Subtask 57-26-13-560-051
 A. Preparation for Installation
 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (1)
 Clean the component interfaces and the adjacent areas with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-004).

 (2)
 Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-004) to clean the edges of the bush (2) and the adjacent area.

 (3)
 Do an inspection of the component interface and/or the adjacent area.

 (4)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 (5)
 Apply a layer of SEALANTS (Material No. 09-002) around the edges of the bush (3).

 Subtask 57-26-13-420-053
 B. Installation of the Bearing Assembly
 (1)
 Install the special washer (2) in the actuator attachment bracket. Make sure that the special washer (2) is correctly located on the lug of the actuator attachment-bracket.

 (2)
 Clean the special washer (2) and the bearing housing (1) with a clean lint-free cloth and CLEANING AGENTS (Material No. 11-004).

 (3)
 Apply a bead of SEALANTS (Material No. 09-002) around the anti-rotation washer (3) and the housing of the bearing-assembly (1).

 1EFF : ALL 1 57-26-13Page 421 1 1 May 01/05R 1 1 1CES 1

 (4)
 Install a new tab washer (4).

 (5)
 Use the SPANNER R/I BEARING (98D57004081000) to install the special nut (5). TORQUE the special nut (5) to between 4.0 and 4.5 m.daN

 (29.49 and 33.18 lbf.ft).

 (6)
 Safety the special nut (5) with the tab washer (4).

 (7)
 Clean the component interfaces as follows: WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL

_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (a) Clean the edge of the special nut (5), the special washer (4) and the adjacent areas with a clean MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-004).
 (8) Apply a bead of SEALANTS (Material No. 09-002) around the special nut
 (5) and the special washer (4).
 5. Close-up
________ Subtask 57-26-13-410-051
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 (2) Install the MLG actuating cylinder (Ref. TASK 32-31-46-400-001). Subtask 57-26-13-942-051
 B. Removal of Equipment
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the safety barriers.

 1EFF : ALL 1 57-26-13Page 422 1 1 May 01/05R 1 1 1CES 1

 (3)
 Remove the warning notice(s).

 (4)
 Remove the access platform(s).

 (5)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 57-26-13Page 423 1 1 May 01/05R 1 1 1CES 1

 TASK 57-26-13-000-004
 Removal of the Bearing Seals of the MLG Actuator Bearing Assembly
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(48)