(8.00 to 75.00 lbf.ft) R No specific Torque Wrench : range 2.00 to 20.00 m.daN R (15.00 to 150.00 lbf.ft)
98D57004033000 1 R/I TOOL FLAP BEARING
98D57004034000 1 R/I TOOL FLAP BEARING
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 09-002 USA MIL-S-8802 TYPE I CLASS B
Material No. 09-018 FUEL TANK SEALANTPOLYSULFID(NO LONGER AVAILABLE (Ref. 20-31-00)USA AMS 3267/3 CORROSION INHIBITING LOW ADHESION SEALANT
Material No. 09-019 (Ref. 20-31-00)USA AMS 3267/3 LOW ADHESION CORROSION INHIBITING SEALANT
Material No. 11-026 Material No. 19-003 (Ref. 20-31-00)GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00)USA AMS 3819
Material No. 19-010 LINT-FREE COTTON CLOTH (Ref. 20-31-00)USA AMS 5687
LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA
(Ref. 20-31-00)
R C. Expendable Parts
R -------------------------------------------------------------------------------R FIG.ITEM |DESIGNATION |IPC-CSN R -------------------------------------------------------------------------------
R 1 bearing assembly
R 1 bearing assembly
R 1 bearing assembly
R 3 washer
R 3 washer
R 3 washer
R 4 nut
R 4 nut
R 4 nut
57-26-15 01A-010 57-26-15 05A-010 57-26-15 10A-010 57-26-15 01A-030 57-26-15 05A-030 57-26-15 10A-030 57-26-15 01A-020 57-26-15 05A-020 57-26-15 10A-020
R D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R R R R R R R 27-54-61-000-001 27-54-61-000-003 27-54-61-400-001 27-54-61-400-003 27-54-62-000-001 27-54-62-000-002 27-54-62-400-001 27-54-62-400-002 57-51-33-000-002 57-51-33-000-003 57-51-33-000-004 57-51-33-400-002 57-51-33-400-003 57-51-33-400-004 57-55-11-000-001 57-55-11-000-004 57-55-11-400-001 57-55-11-400-004 Removal of the Inboard Flap Removal of the Inboard Double-Slotted FlapInstallation of the Inboard Flap Installation of the Inboard Double-Slotted FlapRemoval of the Outboard Flap Removal of the Outboard Double-Slotted FlapInstallation of the Outboard Flap Installation of the Outboard Double-Slotted FlapRemoval of the No.2 Flap Track BeamRemoval of the No.3 Flap Track BeamRemoval of the No.4 Flap Track BeamInstallation of the No.2 Flap Track BeamInstallation of the No.3 Flap Track BeamInstallation of the No.4 Flap Track BeamRemoval of the Flap Track Fairings Nos. 2, 3 and 4 Removal of the Flap Track Fairings Nos. 2, 3 and 4Installation of the Flap Track Fairings Nos. 2, 3 and 4 Installation of the Flap Track Fairings Nos. 2, 3 and 4
3. Job Set-up__________
Subtask 57-26-15-941-051
A. Safety Precautions
(1) Make sure that the safety barriers are in position.
(2) Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER is installed on the slat/flap control lever.
(3) Make sure that the warning notices are in position to tell persons not to operate the slat/flap system.
Subtask 57-26-15-865-051
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-26-15-860-050
C. Aircraft Maintenance Configuration
(1)
For the flap track beam 2:
(a)
Make sure that the access platform is below the applicable inboard flap at zone 531(631).
(b)
Make sure that the applicable inboard flap is removed (Ref. TASK 27-54-61-000-001).
中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(54)
