____
 correct repair procedure.

 5. Close-up
________ Subtask 57-26-00-942-063
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the access platform(s).

 (3) Close the main landing gear doors (Ref. TASK 32-12-00-410-001). Subtask 57-26-00-410-066
 B. Removal of Equipment
 (1)
 Remove the safety barriers.

 (2)
 Remove the warning notice(s).

 1EFF : ALL 1 57-26-00Page 685 1 1 Nov 01/04R 1 1 1CES 1

 TASK 57-26-00-200-009
 Detailed Visual Inspection of Outer Wing Bottom Skin Lower Surface Forward Attachment Fitting for Flap Track Beams 2, 3 and 4
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 572658-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific inspection mirror No specific safety barriers No specific suitable light source No specific warning notices No specific access platform 2.5 m (8 ft. 2 in.) 98D27803500001 2 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER B. Consumable Materials

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
 SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
 Material No. 19-003 USA AMS 3819
 LINT-FREE COTTON CLOTH (Ref. 20-31-00)

 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
57-55-11-000-001 Removal of the Flap Track Fairings Nos. 2, 3 and 4 R 57-55-11-000-004 Removal of the Flap Track Fairings Nos. 2, 3 and 4 57-55-11-400-001 Installation of the Flap Track Fairings Nos. 2, 3 and
 4 R 57-55-11-400-004 Installation of the Flap Track Fairings Nos. 2, 3 and R 4
 ASRM 572600 (for corrective action)
 57-26-00-991-014 Fig. 614

 3. Job Set-up
__________
 Subtask 57-26-00-941-063
 A. Safety Precautions
 (1)
 Put the safety barriers in position.

 (2)
 Put warning notices in the cockpit to tell persons not to operate the flaps or slats.

 (3)
 Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.

 Subtask 57-26-00-865-068
 B. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21

R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 Subtask 57-26-00-010-063
 C. Get Access
 (1)
 Put the access platform below the applicable flap track fairings, zones 531(631), 532 (632) and 533(633).

 (2)
 Remove the forward and aft fixed fairings from the No. 2, No.3, and No.4 flap track beams (Ref. TASK 57-55-11-000-001).

 **ON A/C 301-399,
 Subtask 57-26-00-010-063-A
 C. Get Access
 (1)
 Put the access platform below the applicable flap track fairings, zones 531(631), 532 (632) and 533(633).

 (2)
 Remove the forward and aft fixed fairings from the No. 2, No.3, and No.4 flap track beams (Ref. TASK 57-55-11-000-004).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(37)