(b)
Measure the total axial play (Dim 'X'). You must replace the bearing (4) if the total axial play Dim 'X' is more than 0.16 mm (0.0062 in.).
Pylon Rear Attachment Bearing
Figure 401/TASK 57-26-12-991-001
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-26-12Page 404 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
R Pylon Rear Attachment Bearing
R Figure 401A/TASK 57-26-12-991-001-A
R 1EFF : 301-399, 1 57-26-12 Page 405
1 1 May 01/04
1 1
1CES 1
TASK 57-26-12-400-001
Installation of the Pylon Rear Attachment Bearing
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific plastic spatula No specific warning notices No specific access platform 2 m (6 ft. 7 in.) No specific Torque Wrench : range 6.00 to 36.00 m.daN
(50.00 to 260.00 lbf.ft) 98D57004026000 1 SOCKET - PYLON PICK-UP 98D57004027000 1 SPANNER - PYLON PICK-UP
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 09-005 USA MIL-S-81733 CLASS C CORROSION INHIBITIVE INTERFAY SEALANT (Ref. 20-31-00) Material No. 11-026 GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
1EFF : ALL 1 57-26-12Page 406 1 1 May 01/04R 1 1 1CES 1
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
1 slotted nut 57-26-05 02A-020 2 tab washer 57-26-05 02A-030 4 bearing 57-26-05 02A-010
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
54-51-17-000-002 Removal of the Pylon-to-Wing Aft Attach Fitting at RIB10
54-51-17-400-002 Installation of the Pylon-to-Wing Aft Attach Fitting at RIB10
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
57-26-12-991-001 Fig. 401
**ON A/C 301-399,
57-26-12-991-001-A Fig. 401A
**ON A/C ALL
3. Job Set-up
__________
Subtask 57-26-12-941-052
A. Safety Precautions
(1)
Make sure the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER is correctly installed on the flap/slat control lever.
(2)
Make sure that the safety barriers are in position.
(3)
Make sure the warning notices are in position in the cockpit to tell persons not to operate the flaps or slats.
Subtask 57-26-12-860-050
B. Aircraft Maintenance Configuration
(1)
Make sure that the access platform is in position below the applicable pylon rear attachment point.
(2)
Make sure that the aft attach fitting has been removed (Ref. TASK 54-51-17-000-002).
4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 401/TASK 57-26-12-991-001)
**ON A/C 301-399,
(Ref. Fig. 401A/TASK 57-26-12-991-001-A)
**ON A/C ALL
Subtask 57-26-12-210-050
A. Preparation for Installation
(1)
Use a plastic spatula to remove unwanted sealant from the interface of the pylon rear attachment.
(2)
Clean the interface of the bearing (4) and the pylon rear attachment
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(41)
