1EFF : ALL 1 57-26-00Page 639 1 1 May 01/04R 1 1 1CES 1

 Subtask 57-26-00-280-052

 B. Inspection
 (1)
 Do a special detailed inspection of the upper flange radii of the flap track beams 2, 3 and 4 (Ref. NTM 57-26-01 PART 6).

 (2)
 To complete the inspection:

 (a)
 Remove LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever

 (b)
 Retract the flaps (Ref. TASK 27-50-00-866-009) as required, to get access to the flap track beam under the flap track carriage.

 (c)
 Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER on the flap/slat control lever.

 NOTE : If necessary, refer to the ASRM (Ref. ASRM 572600) for the
____ correct repair procedure. If the defect is not included in this repair, you must request a procedure from Airbus Industrie. ________
5. Close-up

R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 Subtask 57-26-00-410-057
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER.

 (3)
 Fully extend the flaps (Ref. TASK 27-50-00-866-008).

 (4)
 Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER on the flap/slat control lever.

 (5)
 Install the applicable flap track fairing access panels (Ref. TASK 57-55-11-400-001)

 (a) for flap track 2, install:
 -531AB, 631AB, 531BB, 631BB, 531CB, 631CB.

 (b) for the flap track 3, Install
 - 532AB, 632AB, 532BB, 632BB, 532CB, 632CB.
 (c) for the flap track 4, Install
 - 533AB, 633AB, 533BB, 633BB, 533CB, 633CB. 
R  **ON A/C 301-399, 
R  Subtask 57-26-00-410-057-A 
R  A. Close Access 
R  (1) Make sure that the work area is clean and clear of tool(s) and other 
R  items. 
R  (2) Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER. 
R  (3) Fully extend the flaps (Ref. TASK 27-50-00-866-008). 
R  (4) Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER on the flap/slat 
R  control lever. 
R  (5) Install the applicable flap track fairing access panels (Ref. TASK 
R  57-55-11-400-004) 
R  (a) for the flap track 2, install: 
R  - 531CB, 631CB, 531EB, 631EB. 
R  (b) for the flap track 3, install: 
R  - 532CB, 632CB, 532EB, 632EB. 
R  (c) for the flap track 4, install: 
R  - 533CB, 633CB, 533EB, 633EB. 
R  **ON A/C ALL
 Subtask 57-26-00-865-055
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit
 breaker(s):
 6CV, 8CV.

 Subtask 57-26-00-866-055

 C. Aircraft Maintenance Configuration
 (1) Retract the flaps (Ref. TASK 27-50-00-866-009). Subtask 57-26-00-942-057
 D. Removal of Equipment
 (1)
 Remove the safety barriers.

 (2)
 Remove the warning notice(s).

 (3)
 Remove the access platform(s).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 57-26-00Page 642 1 1 May 01/04R 1 1 1CES 1

 TASK 57-26-00-200-005
R  Detailed Inspection of Outer Wing, Flap Track Beams 2, 3, 4 Lower Flanges and Lower Channel
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 572604-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(26)