(d)
 Safety the nut (74):

 -
for track 3 positions, use the new cotter pin (75) and/or the new cotter pin (76)

 -
for track 4 positions, use the new cotter pin (77) and/or the new cotter pin (78)

 -
for track 6 positions, use the new cotter pin (79) and/or the new cotter pin (80)

 -
for track 7 positions, use the new cotter pin (81) and/or the new cotter pin (82)

 -
for track 9 positions, use the new cotter pin (83) and/or the new cotter pin (84)

 -
for track 10 positions, use the new cotter pin (85) and/or the new cotter pin (86)

 -
for track 11 positions, use the new cotter pin (87) and/or the new cotter pin (88)

 -
for track 12 positions, use the new cotter pin (89) and/or the new cotter pin (90).

 (4)
 Installation of the top vertical-load rollers at tracks 3, 4, 6, 7, 9, 10, 11 and 12. (Ref. Fig. 402/TASK 57-41-33-991-002)

 (a)
 Apply a thin layer of COMMON GREASE (Material No. 04-024) to the pin (111).

 (b)
 Install the roller (113) and the pin (111).

 (c)
 Make sure that:

 -
the pin (111) is correctly engaged with the eccentric bush

 -
the angled greaser points down and forward (tracks 6, 7, 9 thru 12 aft positions only).

 1EFF : ALL 1 57-41-33Page 413 1 1 May 01/04R 1 1 1CES 1

 (d)
 Install and tighten the nut (95).

 (e)
 Safety the nut (95):

 -
for track 3 positions, use the new cotter pin (96) and/or the new cotter pin (97)

 -
for track 4 positions, use the new cotter pin (98) and/or the new cotter pin (99)

 -
for track 6 positions, use the new cotter pin (100) and/or the new cotter pin (101)

 -
for track 7 positions, use the new cotter pin (102) and/or the new cotter pin (103)

 -
for track 9 positions, use the new cotter pin (104) and/or the new cotter pin (105)

 -
for track 10 positions, use the new cotter pin (106) and/or the new cotter pin (107)

 -
for track 11 positions, use the new cotter pins (108)

 -
for track 12 positions, use the new cotter pin (109) and/or the new cotter pin (110).

 Subtask 57-41-33-710-050
 C. Test
 (1)
 Lubricate the applicable rollers with COMMON GREASE (Material No. 04-024).

 (2)
 Make sure that the rollers that you installed operate without play.

 (3)
 Remove all unwanted grease with a clean lint-free cloth or tissue.

 5. Close-up
________
 Subtask 57-41-33-410-050
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Install the applicable slat tracks:

 -
for slat tracks 1 thru 4 (Ref. TASK 27-84-61-400-004)

 -
for slat tracks 5 thru 12 (Ref. TASK 27-84-62-400-001).

 1EFF : ALL 1 57-41-33Page 414 1 1 May 01/04R 1 1 1CES 1

 (3) Install the applicable slats:
 -
for the rollers at slat tracks 1, 2, 3, and/or 4, install slat No. 1 (Ref. TASK 27-84-63-400-002)

 -
for the rollers at slat tracks 5 and/or 6, install slat No. 2 (Ref. TASK 27-84-64-400-002)

 -
for the rollers at slat tracks 7 and/or 8, install slat No. 3 (Ref. TASK 27-84-65-400-002)

 -
for the rollers at slat tracks 9 and/or 10, install slat No. 4 (Ref. TASK 27-84-66-400-002)

 -
for the rollers at slat tracks 11 and/or 12, install slat No. 5 (Ref. TASK 27-84-67-400-002).

 Subtask 57-41-33-865-052
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 7CV.
 Subtask 57-41-33-942-050
 C. Removal of Equipment
 (1)
 Remove the safety barriers.

 (2)
 Remove the warning notice(s).

 (3)
 Remove the access platform(s).

 (4)
 Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat control lever.

 (5)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 57-41-33Page 415 1 1 May 01/02R 1 1 1CES 1

 ACCESS PANELS AND COVERS - REMOVAL/INSTALLATION
_______________________________________________
 TASK 57-41-37-000-004

 Removal of the Pressure-Relief Panels 521AB(621AB), 521CB(621CB), 521EB(621EB),
 522AB(622AB), 522CB(622CB)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(130)