-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific trestle/table that is sufficiently padded
No specific warning notices
No specific access platform 4 m (13 ft. 1 in.)
98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 57-31-22-991-001-A Fig. 401
3. Job Set-up
__________
Subtask 57-31-22-941-050
A. Safety Precautions
(1) Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
(2) Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(3) Put the safety barriers in position.
(4) Put the access platform below the applicable wing at the wing-tip fence, zone 530 (630).
Subtask 57-31-22-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------122VU LIGHTING/EXT LT/NAV1/AND LOGO/LT 1LA T03 122VU LIGHTING/EXT LT/NAV2/AND LOGO/LT 2LA T02 122VU LIGHTING/WING/STROBE 10LV V05
4. Procedure_________
R (Ref. Fig. 401/TASK 57-31-22-991-001-A)
R Subtask 57-31-22-020-050-A
R A. Removal of the Wing-tip Fence
R (1) Remove the bolts (8) and the covers (7).
R (2) Remove the locking plates (6) and (9).
R R (3) Hold the wing-tip fence (3) (the weight is approximately 11 kg (24 lb)) and remove the bolts (5) and the washers (4).
R R (4) Remove the wing-tip fence laterally from the wing-tip (10) and put it on a trestle/table that is sufficiently padded.
R (5) If necessary, collect the barrel nuts (1) and (2).
R R Wing-Tip Fence Figure 401/TASK 57-31-22-991-001-A
1EFF : 1 1 1CES ALL 1 111 57-31-22 Page 403 May 01/02
TASK 57-31-22-400-001
Installation of the Wing-Tip Fence
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific non-metallic tool No specific plastic spatula No specific warning notices No specific access platform 4 m (13 ft. 1 in.) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R RR R R Material No. 08-002A Material No. 08-048 Material No. 08-058 Material No. 09-005 Material No. 09-016 Material No. 11-026 Material No. 19-003 GENERAL PURPOSE DIMETHACRYLATE GREEN (Ref. 20-31-00)D DA-2-657-4 ADHESIVE (Ref. 20-31-00)GB AFS 1740 ADHESIVE (Ref. 20-31-00) USA MIL-S-81733 CLASS C CORROSION INHIBITIVE INTERFAY SEALANT (Ref. 20-31-00) USA MIL-PRF-81733D TYPE II CLASS B CORROSION INHIBITING FILLET CONSISTENCY (Ref. 20-31-00)GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00)USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(97)
