(4) Make sure that the access platform is in position below the applicable wing-tip, zone 534 (634).
Subtask 57-31-22-865-051
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
122VU LIGHTING/EXT LT/NAV1/AND LOGO/LT 1LA T03 122VU LIGHTING/EXT LT/NAV2/AND LOGO/LT 2LA T02 122VU LIGHTING/WING/STROBE 10LV V05
4. Procedure
_________
(Ref. Fig. 401/TASK 57-31-22-991-001-A) Subtask 57-31-22-420-052-A
A. Preparation for Installation
(1)
Use a plastic spatula to remove used sealant from the wing-tip (10).
(2)
Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the wing-tip (10).
(3)
Do an inspection of the component interface and/or the adjacent area.
(4)
If necessary, install the barrel nuts (1) and (2) as follows:
(a)
Use a non-metallic tool to remove sealant from the holes for the barrel nuts (1) and (2).
(b)
Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the holes for the barrel nuts (1) and (2).
(c)
Apply a layer of SEALANTS (Material No. 09-005) to the barrel nuts (1) and (2).
(d)
Install the barrel nuts (1) and (2) into the holes, with the slot at the bottom. Align the holes for the bolts (5).
1EFF : ALL 1 57-31-22Page 406 1 1 Aug 01/04R 1 1 1CES 1
Subtask 57-31-22-420-050-A
R B. Installation of the Wing-tip Fence
(1) Put the wing-tip fence (3) in position on the wing-tip (10) and hold it on supports.
(2) Apply a layer of SEALANTS (Material No. 09-005) to the bolts (5).
(3) Install the washers (4) and the bolts (5).
(4) TORQUE the bolts (5) to between 2.7 and 3.3 m.daN (19.91 and 24.33 lbf.ft).
R R R (5) Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-002A) or BONDING AND ADHESIVE COMPOUNDS (Material No. 08-058) to the wing-tip fence, where the locking plates (6) and (9) attach.
(6) Install the locking plates (6) and (9). If necessary, adjust the TORQUE of the bolts (5) (in the permitted range), to align the bolts (5) with the locking plates (6) and (9).
(7) Measure the clearances at the top and bottom interfaces of the wing-tip (10) and the wing-tip fence (3): - dimension X (forward of STA WTY 315.0 and aft of STA WTY 799.0) must be between 1.7 mm (0.07 in.) and 2 mm (0.08 in.) over the areas of the filler blocks - dimension Y (between STA WTY 315.0 and STA WTY 799.0) must be smaller than 1 mm (0.04 in.).
(8) Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-048) to the bolts (8).
R (9) Apply SEALANTS (Material No. 09-016) along the interface of wing-tip (10) and the wing-tip fence (3), to make a smooth continuous joint.
(10) Install the covers (7) and the bolts (8).
5. Close-up________
Subtask 57-31-22-865-052
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1LA, 2LA, 10LV.
Subtask 57-31-22-942-051
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) from the flap/slat control lever.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(6)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 57-31-22Page 408 1 1 May 01/02R 1 1 1CES 1
GLAZING - WING TIP NAVIGATION LIGHT - REMOVAL/INSTALLATION
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(98)
