曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  START A TASK ON OR NEAR: 
R  - THE FLIGHT CONTROLS 
R  - THE FLIGHT CONTROL SURFACES 
R  - THE LANDING GEAR AND THE RELATED DOORS 
R  - COMPONENTS THAT MOVE. 
R  1. Reason for the Job__________________ 
R  Refer to the MPD TASK: 572164-01 
R  2. Job Set-up Information______________________ 
R  A. Fixtures, Tools, Test and Support Equipment 
R  -------------------------------------------------------------------------------
R  REFERENCE QTY DESIGNATION 
R  -------------------------------------------------------------------------------
R  No specific circuit breaker(s) safety clip(s) 
R  No specific safety barriers 
R  No specific warning notices 
R  No specific adjustable access platform 4.0 m (13 ft. 1 in.) 
R  98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER 
R  B. Consumable Materials 
R  -------------------------------------------------------------------------------
R  REFERENCE DESIGNATION 
R  -------------------------------------------------------------------------------
R  Material No. 11-026 GB DEF-STAN 68-148/1 
R  SOLVENT GENERAL PURPOSE (Ref. 20-31-00) 
R  Material No. 19-003 USA AMS 3819 
R  LINT-FREE COTTON CLOTH (Ref. 20-31-00) 

R 1EFF : 301-399, 1 57-41-00Page 623 1 1 May 01/04 1 1 1CES 1

R C. Referenced Information

R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R  28-00-00-910-001  Fuel Safety Procedures 
R  ASRM 572100  (for corrective action) 
R  57-41-00-991-024  Fig. 607 
R  57-41-00-991-020  Fig. 608 
R  3. Job Set-up__________ 
R  Subtask 57-41-00-941-068 
R  A. Safety Precautions 

R  WARNING : OBEY THE FUEL SAFETY PROCEDURES._______ 
R  (1) Obey the fuel safety procedures (Ref. TASK 28-00-00-910-001). 
R  (2) Put the safety barriers in position. 
R  (3) Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) 
R  on the flap/slat control lever. 
R  (4) Put warning notices in the cockpit to tell persons not to operate the 
R  flaps or slats. 
R  (5) Put the adjustable access platform in position below the applicable 
R  holes in the wing bottom skin, zone 540/640. 
R  Subtask 57-41-00-865-084 
R  B. Open, safety and tag this(these) circuit breaker(s): 
R  -------------------------------------------------------------------------------
R  PANEL  DESIGNATION  IDENT. LOCATION 
R  -------------------------------------------------------------------------------
R  49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1  5CV  B06 
R  121VU FLIGHT CONTROLS/SLT/CTL/SYS2  7CV  R21 

R 1EFF : 301-399, 1 57-41-00Page 624 1 1 May 01/04 1 1 1CES 1

R 4. Procedure
_________

R  Subtask 57-41-00-110-063 
R  A. Preparation for Inspection 
R  (1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING 
R  AGENTS (Material No. 11-026) to clean 
R  - the wing bottom skin around the fuel tank water drain holes 
R  - the magnetic level indicators and the hole edges. 
R  Subtask 57-41-00-210-067 
R  B. Inspection 
R  (Ref. Fig. 607/TASK 57-41-00-991-024) 
R  (1) Examine the fuel tank water drain hole in the wing bottom skin 
R  between RIBS 22-23. 
R  Make sure that: 
R  - there is no damage 
R  - the edges are not corroded 
R  - the surface finish of the edges is in good condition 
R  - there are no signs of fuel leakages. 
R  NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) for the____ 
R  correct repair procedure. 
R  (2) Examine the magnetic level indicator between rib 15 and 16. 
R  (Ref. Fig. 608/TASK 57-41-00-991-020) 
R  Make sure that: 
R  - the hole edges are not damaged 
R  - the sight collar is in good condition 
R  - the surface finish of the hole edges is in the correct condition 
R  - there is no fuel leakage 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(113)