-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1EFF : 301-399, 1 57-53-00Page A678 1 1 Nov 01/04R 1 1 1CES 1
Outboard Flap - Track 3 Support Attachments - Inspection Area Figure 625/TASK 57-53-00-991-029
1EFF : 301-399, 1 57-53-00Page A679 1 1 Nov 01/04R 1 1 1CES 1
Subtask 57-53-00-110-080
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the support fitting, the attachment bracket, the attachment structure and the internal support structure.
Subtask 57-53-00-210-071
B. Inspection
(1)
Do an inspection of the support fitting, the attachment bracket and the attachment structure. Make sure that:
-
there is no damage
-
there is no corrosion
-
there are no cracks or scores
-
the support fitting, attachment bracket and drive bracket are installed correctly
-
the surface protection is in the correct condition.
(2)
Do an inspection of the internal support structure where it can be seen. Make sure that:
-
there is no damage
-
there is no corrosion
-
there are no cracks or scores
-
the support fitting, attachment bracket and drive bracket are installed correctly
-
the surface protection is the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575300) for the
____
correct repair procedure.
5. Close-up
________
Subtask 57-53-00-410-075
A. Close Access
(1)
Remove the spark-proof lamp from the inspection area.
(2)
Install the applicable access panel in the bottom skin at track 3:
-
for the left wing, install 587AB
-
for the right wing, install 687AB.
1EFF : 301-399, 1 57-53-00Page A680 1 1 Nov 01/04R 1 1 1CES 1
(3)
Install the applicable flap track fairings (Ref. TASK 57-55-11-400-004):
-
for the left wing, install 532AT, 532CB
-
for the right wing, install 632AT, 632CB.
(4)
Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 57-53-00-865-112
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-53-00-860-055
C. Aircraft Maintenance Configuration
(1) Fully retract the flaps (Ref. TASK 27-50-00-866-009). Subtask 57-53-00-942-079
D. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Remove the safety barriers.
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : 301-399, 1 57-53-00Page A681 1 1 Nov 01/04R 1 1 1CES 1
TASK 57-53-00-220-015
Special Detailed Inspection of Outboard Double Slotted Flap, Internal Support Fitting at Track 3, Including Attachment Bracket, Drive Bracket ....
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575329-02 Special Detailed Inspection of Outboard Double Slotted Flap, Internal Support Fitting at Track 3, Including Attachment Bracket, Drive Bracket and Attachment Structure, Internal and External, LH/RH
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(10)
