-
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 575316-02
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific safety barriers
 No specific warning notices
 No specific access platform 2.5 m (8 ft. 2 in.)

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 08-061A  D DAN 220 ALUMINIUM FOIL ADHESIVE TAPE (Ref. 20-31-00)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page A653 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 C. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground 27-50-00-866-009 Retraction of the Flaps on the Ground 27-54-62-000-003 Removal of the Leading Edge Panels 2 and 5 on the
 Outboard Flap 27-54-62-400-003 Installation of the Leading Edge Panels 2 and 5 on
 the Outboard Flap 57-55-11-000-001 Removal of the Flap Track Fairings Nos. 2, 3 and 4 57-55-11-400-001 Installation of the Flap Track Fairings Nos. 2, 3 and
 4
 NTM 57-53-16 PART 9
 ASRM 575300 (for corrective action)

 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-214,
 57-53-00-991-024 Fig. 622
R **ON A/C 106-149, 215-299, 401-499,
 57-53-00-991-024-A Fig. 622A
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 3. Job Set-up
__________
 Subtask 57-53-00-941-074
 A. Safety Precautions
 (1)
 Put warning notices in the cockpit to tell persons not to operate the flaps or slats.

 (2)
 Put the safety barriers in position.

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page A654 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 Subtask 57-53-00-860-123

 B. Aircraft Maintenance Configuration
 (1)
 Extend the flaps fully (Ref. TASK 27-50-00-866-008).

 (2)
 Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is on the slat/flap control lever.

 Subtask 57-53-00-865-101
 C. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-214,
 Subtask 57-53-00-010-073
 D. Get Access
 (1)
 Put the access platform below the applicable wing trailing edge at flap track 4, zone 533 (633). (Ref. Fig. 622/TASK 57-53-00-991-024)

 (2)
 Remove the access panel 533AT (633AT) and the flap track 4 fairing 533CB (633CB) (Ref. TASK 57-55-11-000-001).

 (3)
 Remove the outboard flap leading edge panel 5 (Ref. TASK 27-54-62-000-003).

 (4)
 Remove and discard the cover from the RH inspection hole on the front spar.

 (5)
 Make sure that the inspection hole is clear of unwanted material.

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page A655 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 Outboard Flap
 Figure 622/TASK 57-53-00-991-024

R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 57-53-00Page A656 1201-214, 1May 01/05 1 1 1CES 1

R  **ON A/C 106-149, 215-299, 401-499,
 Subtask 57-53-00-010-073-A
 D. Get Access
 (1) Put the access platform below the applicable wing trailing edge at flap track 4, zone 533 (633). (Ref. Fig. 622A/TASK 57-53-00-991-024-A)
 (2) Remove the access panel 533AT (633AT) and the flap track 4 fairing 533CB (633CB) (Ref. TASK 57-55-11-000-001).
 (3) Remove and discard the cover(s) from the applicable inspection hole(s) on the front spar.
 (4) Make sure that the applicable inspection hole is clear of unwanted material. 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(4)