曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R R R R R R R R  12-22-27-640-004 27-50-00-866-009 27-54-00-710-001 29-23-00-860-001 29-23-00-860-002 57-55-11-000-001 57-55-11-000-004 12-22-27-640-004 57-55-00-991-001  Lubrication of all Flap Track Carriage RollersRetraction of the Flaps on the Ground Operational Test of the Flap System Disconnection of the Isolation Coupling of the Power Transfer Unit (PTU) Connection of the Isolation Coupling of the Power Transfer Unit (PTU)Removal of the Flap Track Fairings Nos. 2, 3 and 4 Removal of the Flap Track Fairings Nos. 2, 3 and 4 Lubrication of all Flap Track Carriage Rollers (for corrective action)Fig. 401
 3. Job Set-up__________
 Subtask 57-55-00-941-055
 A. Safety Precautions
 (1) Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
 (2) Put the safety barriers in position.
 Subtask 57-55-00-860-050
 B. Aircraft Maintenance Configuration
 (1) Make sure that the flaps are fully retracted (Ref. TASK 27-50-00-866-009).
 (2) Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
 (3) Put the adjustable access platform below the applicable flap track 2, 3 or 4, zone 531(631), 532 (632) or 533(633).

 

 Subtask 57-55-00-865-058
 C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
 4. Procedure
_________
 (Ref. Fig. 401/TASK 57-55-00-991-001)
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
 EDGE:

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 Subtask 57-55-00-040-052
 A. Deactivation of the Damaged Fairing
 (1)
 Remove the applicable damaged fairing (Ref. TASK 57-55-11-000-001).

 (2)
 Write in the aircraft log that the flap-track fairing has been deactivated.

 NOTE : It may be necessary to lubricate the deactivated flap-track
____ assembly (because of bad weather and the local conditions) (Ref. TASK 12-22-27-640-004).

 Safety of the Flap Interconnect- Strut Electrical Harness
 Figure 401/TASK 57-55-00-991-001

R **ON A/C 301-399,

R  Subtask 57-55-00-040-052-A 
R  A. Deactivation of the Damaged Fairing 
R  (1) Remove the applicable damaged fairing (Ref. TASK 57-55-11-000-004). 
R  (2) For the track 2 position only, attach the electrical harnesses to 
R  aircraft structure as follows: 
R  CAUTION : DO NOT TIGHTEN THE CABLE TIE THAT IS USED AS A GUIDE FOR_______ 
R  THE ELECTRICAL HARNESSES. 
R  IF THE TIE IS TOO TIGHT, THE HARNESSES CANNOT MOVE WHEN THE 
R  FLAPS ARE EXTENDED OR RETRACTED. 
R  (a) Examine the electrical harnesses (9) for correct condition. 
R  (b) Attach the electrical harnesses (9) together at distances of 150 
R  mm (6.0 in.) to 200 mm (8.0 in.) with the cable ties (3). 
R  (c) Connect the electrical harnesses (9) to the interface connectors 
R  (6) then: 
R  - put the electrical harnesses (9) in position along the flap 
R  drive-arm (7) and the fairing drive-lever (4) 
R  - put the interface connectors (6) in the aft recess of the flap 
R  drive-arm (7). 
R  (d) Install the cable ties (3) to loosely hold the interface 
R  connectors (6) and the electrical harnesses (9). Put the cable 
R  ties (3) at distances of between 25 mm (0.9842 in.) and 50 mm 
R  (1.9685 in.) at: 
R  - the fairing drive-lever (4) 
R  - the flap link-arm (8) 
R  - the flap drive-lever (7). 
R  (e) Attach the electrical harnesses (3) at point 'Y' with the two 
R  cable ties (3). 
R  (f) Attach the electrical harnessses (9) to the flap drive lever (7) 
R  at point 'X' with the two cable ties (3). 
R  (g) Make the loops, at point 'Z', of the electrical harnesses (9) 
R  that are to pass through point 'X'. Make the loops in the correct 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(43)