Aileron - Hinge Fittings and Actuator Attachment Fittings Figure 602/TASK 57-60-00-991-002
1EFF : ALL 1 57-60-00Page 610 1 1 Aug 01/99R 1 1 1CES 1
Subtask 57-60-00-110-051
A. Preparation for Inspection
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-004) to clean the aileron actuator attachment fittings and the hinge fittings.
Subtask 57-60-00-866-050
B. Manually move the aileron to get access to the actuators and the hinges.
NOTE : The internal flutter dampening system of the actuators will keep
____
the aileron in position.
Subtask 57-60-00-210-051
C. Inspection
(1) Examine the hinge fittings and the actuator attachment fittings. Make sure that:
-
there is no damage
-
there is no corrosion
-
there are no cracks
-
the components are correctly attached
-
the surface protection is in the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 576000) for the
____
correct repair procedure.
1EFF : ALL 1 57-60-00Page 611 1 1 Aug 01/99R 1 1 1CES 1
5. Close-up
________
Subtask 57-60-00-410-050
A. Close Access
(1) Install the access panels 575AT, 575KB, 575LB, 575MB, 675AT, 675KB, 675LB, 675MB.
Subtask 57-60-00-865-053
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 7CV, 15CE1, 15CE2, 16CE1, 16CE2
Subtask 57-60-00-942-051
C. Removal of Equipment
(1)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) from the flap/slat control lever.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the safety barriers.
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-60-00Page 612 1 1 Aug 01/99R 1 1 1CES 1
TASK 57-60-00-200-003
Detailed Visual Inspection of Aileron Upper and Lower External Skins at Attachment to Trailing Edge and Inboard and Outboard Edges
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
R R R R R CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:_______ - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job__________________
Refer to the MPD TASK: 576104-01
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific No specific No specific No specific 98D27803500001 circuit breaker(s) safety clip(s)safety barrierswarning noticesaccess platform 3.8 m (12 ft. 6 in.)1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM WINGS 機(jī)翼5(85)
